Witam.
Dzisiaj zainstalowałem sobie linuxa -SuSE 10.2 - i pomimo ze jest to juz moj drugi linux nadal jestem newbie
![Sad :(](http://forum.linux.pl/Smileys/default/sad.gif)
Problem polega na tym ze ni jak nie mogę polączyć sie z internetem....podczas instalacji nie mogłem sie polaczyc z aktualizacją on-line (a nic nie zmienialem) potem nie moglem zarejestrowac repozytoriów
![Sad :(](http://forum.linux.pl/Smileys/default/sad.gif)
, wiec zaczełem zmieniać ustawienia karty sieciowej.
Ustawialem na automatyczne, ustawialem recznie swoj zewnetrzny ip i bramę ale nic :
![Sad :(](http://forum.linux.pl/Smileys/default/sad.gif)
![Sad :(](http://forum.linux.pl/Smileys/default/sad.gif)
.
Wpisując w konsoli ifconfig wyswietla mi cos takiego:
-------------------------------------------------------------------------------------
dash4:/home/daniel # ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:0E:35:B3:A5:59
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:225 Memory:c0001000-c0001fff
eth1 Link encap:Ethernet HWaddr 00:0F:B0:7F:DF:56
inet addr:85.31.241.20 Bcast:85.31.241.31 Mask:255.255.255.240
inet6 addr: fe80::20f:b0ff:fe7f:df56/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:20352 errors:0 dropped:0 overruns:0 frame:0
TX packets:666 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2317845 (2.2 Mb) TX bytes:56354 (55.0 Kb)
Interrupt:209 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:90 errors:0 dropped:0 overruns:0 frame:0
TX packets:90 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:5868 (5.7 Kb) TX bytes:5868 (5.7 Kb)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
----------------------------------------------------------------------------------------------
dash4:/home/daniel # route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
i16.osiedle.net * 255.255.255.240 U 0 0 0 eth1
loopback * 255.0.0.0 U 0 0 0 lo
default i17.osiedle.net 0.0.0.0 UG 0 0 0 eth1
dash4:/home/daniel #
------------------------------------------------------------------------------------------------
Jako ze ni za bardzo sie na tym znam, wiec nie jestem pewien ale wydaje mi sie ze jednak jakis sygnal komputer odbiera???
Moj komp to laptop- Aristo smart 400
Proszę o dokladny opis konfiguracji polaczenia internetowego , co,gdzie jak. Sam bym tego poszukał, ale niebardzo mam teraz dostep do internetu, wiec niemam gdzie szukac :/ (pisze to u kolegi)
PS: Kiedys moj brat instalował SuSE 10.2 i jemu bez problemow poszlo, wszystko ladnie smigalo.(na stacjonarnym PC)
Z gory dziekuję za odp i czekam na nią z niecierpliwością
Pozdrawiam