Nowe posty

Autor Wątek: Techiclan Wusb-54gr [OK]  (Przeczytany 9005 razy)

Offline

  • Users
  • Nowy na forum
  • *
  • Wiadomości: 6
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« dnia: 2009-12-03, 16:19:59 »
Czy ta karta sieciowa działa na Linux Mandriva 2010?? Jeśli tak to czy ktoś ma do niej sterowniki ponieważ nie mam oryginalnej płyty???

Offline

  • Users
  • Stały bywalec
  • ***
  • Wiadomości: 225
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« Odpowiedź #1 dnia: 2009-12-04, 04:01:16 »
Prosimy o
lspci -vv
inaczej się nie dowiemy. Nie będziemy szukać za ciebie na jakim sprzęcie jest oparta ta karta sieciwa.

Offline flak

  • Users
  • Guru
  • *****
  • Wiadomości: 756
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« Odpowiedź #2 dnia: 2009-12-04, 10:02:14 »
To karta z chipsetem Ralinka obsługiwana przez standardowy sterownik rt73usb. Przynajmniej tak mówi internet.  Daj

lsmod
i sprawdź czy w liście załadowanych modułów widzisz rt73usb czy coś w tym rodzaju. Jeśli widzisz ten moduł (a zdecydowanie powinieneś) to karta jest rozpoznana i działa normalnie w systemie.
 
P.S. To nie jest Windows żeby sterowniki były dołączane na jakiejś płycie. Standardowo sterowniki są osadzane w systemie.

Offline

  • Users
  • Nowy na forum
  • *
  • Wiadomości: 6
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« Odpowiedź #3 dnia: 2009-12-04, 15:43:51 »
to tekst który mi wyskoczyl po wpisaniu ispci -vv:
00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Capabilities:
Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d8100000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1800 [size=8]
Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at d8200000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at [disabled]
Capabilities:
Kernel driver in use: i915
Kernel modules: i915, intelfb

00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Region 0: Memory at d8180000 (32-bit, non-prefetchable) [size=512K]
Capabilities:

00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at d8240000 (64-bit, non-prefetchable) [size=16K]
Capabilities:
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel

00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d6000000-d7ffffff
Prefetchable memory behind bridge: 00000000d2000000-00000000d3ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d4000000-d5ffffff
Prefetchable memory behind bridge: 00000000d0000000-00000000d1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:
Kernel driver in use: pcieport-driver
Kernel modules: shpchp

00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd

00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d8444000 (32-bit, non-prefetchable) [size=1K]
Capabilities:
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d8000000-d80fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities:

00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Capabilities:
Kernel modules: intel-rng, iTCO_wdt

00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02) (prog-if 80 [Master])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 18b0 [size=16]
Capabilities:
Kernel driver in use: ata_piix
Kernel modules: ata_piix

00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18c0 [size=32]
Kernel modules: i2c-i801

02:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)
Subsystem: Hewlett-Packard Company Compaq 6710b or nx9420 Notebook
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 26
Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=4K]
Capabilities:
Kernel driver in use: iwl3945
Kernel modules: iwl3945

05:05.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d8001000 (32-bit, non-prefetchable) [size=2K]
Capabilities:
Kernel driver in use: ohci1394
Kernel modules: ohci1394

05:05.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 17
Region 0: Memory at d8001800 (32-bit, non-prefetchable) [size=256]
Capabilities:
Kernel driver in use: sdhci-pci
Kernel modules: sdhci-pci

05:05.2 System peripheral: Ricoh Co Ltd R5C843 MMC Host Controller (rev 0a)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 3
Region 0: Memory at d8001c00 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities:
Kernel driver in use: ricoh-mmc
Kernel modules: ricoh_mmc

05:05.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 05)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- Interrupt: pin B routed to IRQ 3
Region 0: Memory at d8002000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities:

05:05.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev ff) (prog-if ff)
!!! Unknown header type 7f

05:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02)
Subsystem: Hewlett-Packard Company Device 30bb
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- Latency: 64 (2000ns min, 14000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 4000 [size=64]
Capabilities:
Kernel driver in use: e100
Kernel modules: e100
2. jak sprawwdic lsmod?
3. W konfiguracji nowego interfejsu sieciowego jest coś takiego :
wlan1: Ralink 802.11 bg WLAN

Offline flak

  • Users
  • Guru
  • *****
  • Wiadomości: 756
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« Odpowiedź #4 dnia: 2009-12-05, 14:20:09 »
lspci jest do urządzeń na pci. Tak karta jest na usb. Więc jeśli chcesz się coś o niej dowiedzieć to proponuję lsusb -vv, choć w tym momencie i tak wiemy już wszystko.

lsmod uruchamiasz tak samo jak lspci :)

Skoro ifconfig/iwconfig widzi twoją kartę jako wlan1 to karta jest wykryta (więc automatycznie jest załadowany jej moduł sterownika), to jest gotowa do pracy. Jak sądzę wlan0 to tak karta intelowa (obsługiwana przez moduł "iwl3945"). Podsumowując starczy uruchomić NetworkManager czy Wicd i podłączyć się do sieci.


P.S. Zakładam że jest sens posiadać 2 karty sieci wireless w jednym laptopie.

Offline

  • Users
  • Nowy na forum
  • *
  • Wiadomości: 6
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« Odpowiedź #5 dnia: 2009-12-05, 15:59:54 »
Cytat: flak
starczy uruchomić NetworkManager czy Wicd i podłączyć się do sieci.
Czy to są programy zainstalowane w systemie czy trzeba je ściągnać z neta??

P.S. Mój usługodawca proponuje tylko internet pod USB z antenką wiedz innej mozliwosci niema bo przez karte wbudowana nie łapie neta.

Offline flak

  • Users
  • Guru
  • *****
  • Wiadomości: 756
    • Zobacz profil
Techiclan Wusb-54gr [OK]
« Odpowiedź #6 dnia: 2009-12-07, 08:39:03 »
Nie wiem na jakiej zasadzie twój usługodawca dostarcza internet. Normalnie jak do Access Pointa można się połączyć przez NetworkManagera lub wicd. Albo jeden albo drugi jest zainstalowany w systemie. Wskaż temu którego będziesz używać aby łączył się przez wlan1 a nie wlan0.