dmesg wyświetla to :
[ 21.545366] Memory: 1028308k/1048512k available (1992k kernel code, 19464k reserved, 900k data, 328k init, 131008k highmem)
[ 21.545377] virtual kernel memory layout:
[ 21.545378] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 21.545379] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 21.545380] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 21.545382] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 21.545383] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 21.545384] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB)
[ 21.545386] .text : 0xc0100000 - 0xc02f2374 (1992 kB)
[ 21.545389] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 21.625147] Calibrating delay using timer specific routine.. 3620.90 BogoMIPS (lpj=7241807)
[ 21.625184] Security Framework v1.0.0 initialized
[ 21.625191] SELinux: Disabled at boot.
[ 21.625205] Mount-cache hash table entries: 512
[ 21.625324] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
[ 21.625332] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 21.625335] CPU: L2 Cache: 512K (64 bytes/line)
[ 21.625337] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
[ 21.625347] Compat vDSO mapped to ffffe000.
[ 21.625351] Remapping vsyscall page to ffffe000
[ 21.625360] Checking 'hlt' instruction... OK.
[ 21.641233] SMP alternatives: switching to UP code
[ 21.641408] Freeing SMP alternatives: 11k freed
[ 21.641586] Early unpacking initramfs... done
[ 21.947415] ACPI: Core revision 20060707
[ 21.949591] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 21.952979] CPU0: AMD Athlon(tm) 64 Processor 3000+ stepping 02
[ 21.952993] Total of 1 processors activated (3620.90 BogoMIPS).
[ 21.953130] ENABLING IO-APIC IRQs
[ 21.953310] ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 22.100386] Brought up 1 CPUs
[ 22.100576] Booting paravirtualized kernel on bare hardware
[ 22.100623] Time: 11:42:27 Date: 05/10/107
[ 22.100646] NET: Registered protocol family 16
[ 22.100712] EISA bus registered
[ 22.100716] ACPI: bus type pci registered
[ 22.104911] PCI: PCI BIOS revision 3.00 entry at 0xfb620, last bus=5
[ 22.104913] PCI: Using configuration type 1
[ 22.104915] Setting up standard PCI resources
[ 22.114107] ACPI: Interpreter enabled
[ 22.114110] ACPI: Using IOAPIC for interrupt routing
[ 22.114601] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 22.114604] PCI: Probing PCI hardware (bus 00)
[ 22.115275] PCI: Transparent bridge - 0000:00:09.0
[ 22.115472] Boot video device is 0000:05:00.0
[ 22.115555] ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
[ 22.187886] ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
[ 22.189602] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 22.189954] ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.190305] ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 22.190657] ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 22.191007] ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.191358] ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 22.191708] ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.192059] ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 22.192416] ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.192767] ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.193117] ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[ 22.193471] ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 22.193822] ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.194185] ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[ 22.194548] ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[ 22.194914] ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[ 22.195308] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 22.195696] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 22.196083] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 22.196478] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 22.196777] ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
[ 22.197181] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[ 22.197579] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
[ 22.197977] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 22.198376] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
[ 22.198773] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
[ 22.199171] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[ 22.199573] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[ 22.199971] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 22.200387] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
[ 22.200796] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[ 22.201206] ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
[ 22.204370] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 22.204379] pnp: PnP ACPI init
[ 22.209937] pnp: PnP ACPI: found 15 devices
[ 22.209942] PnPBIOS: Disabled by ACPI PNP
[ 22.209983] PCI: Using ACPI for IRQ routing
[ 22.209987] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 22.234533] NET: Registered protocol family 8
[ 22.234535] NET: Registered protocol family 20
[ 22.234938] pnp: 00:01: ioport range 0x1000-0x107f could not be reserved
[ 22.234941] pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
[ 22.234943] pnp: 00:01: ioport range 0x1400-0x147f has been reserved
[ 22.234946] pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved
[ 22.234949] pnp: 00:01: ioport range 0x1800-0x187f has been reserved
[ 22.234952] pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
[ 22.235161] PCI: Bridge: 0000:00:09.0
[ 22.235163] IO window: 9000-9fff
[ 22.235166] MEM window: f2000000-f3ffffff
[ 22.235168] PREFETCH window: disabled.
[ 22.235171] PCI: Bridge: 0000:00:0b.0
[ 22.235173] IO window: 6000-6fff
[ 22.235175] MEM window: disabled.
[ 22.235177] PREFETCH window: disabled.
[ 22.235180] PCI: Bridge: 0000:00:0c.0
[ 22.235182] IO window: 8000-8fff
[ 22.235184] MEM window: disabled.
[ 22.235186] PREFETCH window: disabled.
[ 22.235189] PCI: Bridge: 0000:00:0d.0
[ 22.235191] IO window: 7000-7fff
[ 22.235193] MEM window: disabled.
[ 22.235195] PREFETCH window: disabled.
[ 22.235200] PCI: Bridge: 0000:00:0e.0
[ 22.235202] IO window: a000-afff
[ 22.235204] MEM window: f0000000-f1ffffff
[ 22.235207] PREFETCH window: e0000000-efffffff
[ 22.235214] PCI: Setting latency timer of device 0000:00:09.0 to 64
[ 22.235221] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 22.235227] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 22.235233] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 22.235238] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 22.235263] NET: Registered protocol family 2
[ 22.272129] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 22.272267] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 22.272987] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 22.273329] TCP: Hash tables configured (established 131072 bind 65536)
[ 22.273332] TCP reno registered
[ 22.284165] checking if image is initramfs... it is
[ 22.886487] Freeing initrd memory: 6772k freed
[ 22.886833] audit: initializing netlink socket (disabled)
[ 22.886844] audit(1181475747.448:1): initialized
[ 22.886896] highmem bounce pool size: 64 pages
[ 22.886957] VFS: Disk quotas dquot_6.5.1
[ 22.886976] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 22.887021] io scheduler noop registered
[ 22.887023] io scheduler anticipatory registered
[ 22.887025] io scheduler deadline registered
[ 22.887036] io scheduler cfq registered (default)
[ 22.887071] PCI: Found disabled HT MSI Mapping on 0000:00:0b.0
[ 22.887078] PCI: Found enabled HT MSI Mapping on 0000:00:00.0
[ 22.887084] PCI: Found disabled HT MSI Mapping on 0000:00:0c.0
[ 22.887092] PCI: Found enabled HT MSI Mapping on 0000:00:00.0
[ 22.887098] PCI: Found disabled HT MSI Mapping on 0000:00:0d.0
[ 22.887106] PCI: Found enabled HT MSI Mapping on 0000:00:00.0
[ 22.887111] PCI: Found disabled HT MSI Mapping on 0000:00:0e.0
[ 22.887119] PCI: Found enabled HT MSI Mapping on 0000:00:00.0
[ 22.887267] PCI: Setting latency timer of device 0000:00:0b.0 to 64
[ 22.887288] assign_interrupt_mode Found MSI capability
[ 22.887291] Allocate Port Service[0000:00:0b.0:pcie00]
[ 22.887346] PCI: Setting latency timer of device 0000:00:0c.0 to 64
[ 22.887366] assign_interrupt_mode Found MSI capability
[ 22.887368] Allocate Port Service[0000:00:0c.0:pcie00]
[ 22.887423] PCI: Setting latency timer of device 0000:00:0d.0 to 64
[ 22.887443] assign_interrupt_mode Found MSI capability
[ 22.887445] Allocate Port Service[0000:00:0d.0:pcie00]
[ 22.887497] PCI: Setting latency timer of device 0000:00:0e.0 to 64
[ 22.887517] assign_interrupt_mode Found MSI capability
[ 22.887519] Allocate Port Service[0000:00:0e.0:pcie00]
[ 22.887614] isapnp: Scanning for PnP cards...
[ 23.239646] isapnp: No Plug & Play device found
[ 23.262903] Real Time Clock Driver v1.12ac
[ 23.262941] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 23.263037] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.263189] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 23.263670] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 23.263871] mice: PS/2 mouse device common for all mice
[ 23.264277] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 23.264429] input: Macintosh mouse button emulation as /class/input/input0
[ 23.264455] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 23.264458] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 23.264595] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 23.267992] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 23.267997] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 23.268148] EISA: Probing bus 0 at eisa.0
[ 23.268153] Cannot allocate resource for EISA slot 1
[ 23.268165] Cannot allocate resource for EISA slot 6
[ 23.268167] Cannot allocate resource for EISA slot 7
[ 23.268169] Cannot allocate resource for EISA slot 8
[ 23.268170] EISA: Detected 0 cards.
[ 23.298195] TCP cubic registered
[ 23.298204] NET: Registered protocol family 1
[ 23.298224] Using IPI No-Shortcut mode
[ 23.298268] ACPI: (supports S0 S1 S4 S5)
[ 23.298312] Magic number: 11:599:731
[ 23.298358] Time: tsc clocksource has been installed.
[ 23.298631] Freeing unused kernel memory: 328k freed
[ 23.319190] input: AT Translated Set 2 keyboard as /class/input/input1
[ 24.530733] Capability LSM initialized
[ 24.569926] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707]
[ 25.070810] usbcore: registered new interface driver usbfs
[ 25.070829] usbcore: registered new interface driver hub
[ 25.070850] usbcore: registered new device driver usb
[ 25.071950] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23
[ 25.071959] ACPI: PCI Interrupt 0000:00:02.1
-> Link [APCL] -> GSI 23 (level, low) -> IRQ 16
[ 25.071969] PCI: Setting latency timer of device 0000:00:02.1 to 64
[ 25.071972] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 25.072093] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 25.072120] ehci_hcd 0000:00:02.1: debug port 1
[ 25.072123] PCI: cache line size of 64 is not supported by device 0000:00:02.1
[ 25.072134] ehci_hcd 0000:00:02.1: irq 16, io mem 0xfeb00000
[ 25.072139] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 25.072210] usb usb1: configuration #1 chosen from 1 choice
[ 25.072231] hub 1-0:1.0: USB hub found
[ 25.072238] hub 1-0:1.0: 10 ports detected
[ 25.115129] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
[ 25.148815] ieee1394: Initialized config rom entry `ip1394'
[ 25.169356] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 25.224782] SCSI subsystem initialized
[ 25.229181] libata version 2.20 loaded.
[ 25.232601] sata_nv 0000:00:07.0: version 3.3
[ 25.233048] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
[ 25.233056] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 17
[ 25.233065] sata_nv 0000:00:07.0: Using ADMA mode
[ 25.233075] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 25.233141] ata1: SATA max UDMA/133 cmd 0xf8876480 ctl 0xf88764a0 bmdma 0x0001c400 irq 17
[ 25.238961] ata2: SATA max UDMA/133 cmd 0xf8876580 ctl 0xf88765a0 bmdma 0x0001c408 irq 17
[ 25.238978] scsi0 : sata_nv
[ 25.325352] Floppy drive(s): fd0 is 1.44M
[ 25.384202] FDC 0 is a post-1991 82077
[ 25.626464] usb 1-8: new high speed USB device using ehci_hcd and address 3
[ 25.710335] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 25.723339] ata1.00: ata_hpa_resize 1: sectors = 240121728, hpa_sectors = 240121728
[ 25.723344] ata1.00: ATA-7: Maxtor 6L120M0, BANC1G10, max UDMA/133
[ 25.723347] ata1.00: 240121728 sectors, multi 16: LBA NCQ (depth 31/32)
[ 25.735279] ata1.00: ata_hpa_resize 1: sectors = 240121728, hpa_sectors = 240121728
[ 25.735283] ata1.00: configured for UDMA/133
[ 25.735291] scsi1 : sata_nv
[ 25.773616] usb 1-8: configuration #1 chosen from 1 choice
[ 26.209500] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 26.222499] ata2.00: ata_hpa_resize 1: sectors = 240121728, hpa_sectors = 240121728
[ 26.222504] ata2.00: ATA-7: Maxtor 6L120M0, BANC1G10, max UDMA/133
[ 26.222507] ata2.00: 240121728 sectors, multi 16: LBA NCQ (depth 31/32)
[ 26.234455] ata2.00: ata_hpa_resize 1: sectors = 240121728, hpa_sectors = 240121728
[ 26.234458] ata2.00: configured for UDMA/133
[ 26.234550] scsi 0:0:0:0: Direct-Access ATA Maxtor 6L120M0 BANC PQ: 0 ANSI: 5
[ 26.234558] ata1: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[ 26.235014] scsi 1:0:0:0: Direct-Access ATA Maxtor 6L120M0 BANC PQ: 0 ANSI: 5
[ 26.235019] ata2: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
[ 26.235720] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
[ 26.235729] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 18
[ 26.235738] sata_nv 0000:00:08.0: Using ADMA mode
[ 26.235750] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 26.235804] ata3: SATA max UDMA/133 cmd 0xf8878480 ctl 0xf88784a0 bmdma 0x0001d800 irq 18
[ 26.235842] ata4: SATA max UDMA/133 cmd 0xf8878580 ctl 0xf88785a0 bmdma 0x0001d808 irq 18
[ 26.235852] scsi2 : sata_nv
[ 26.548919] ata3: SATA link down (SStatus 0 SControl 300)
[ 26.548929] scsi3 : sata_nv
[ 26.864390] ata4: SATA link down (SStatus 0 SControl 300)
[ 26.866303] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 20
[ 26.866312] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 20 (level, low) -> IRQ 19
[ 26.866318] PCI: Setting latency timer of device 0000:00:0a.0 to 64
[ 26.866324] forcedeth: using HIGHDMA
[ 26.879807] SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
[ 26.879823] sda: Write Protect is off
[ 26.879825] sda: Mode Sense: 00 3a 00 00
[ 26.879837] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.879884] SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
[ 26.879892] sda: Write Protect is off
[ 26.879894] sda: Mode Sense: 00 3a 00 00
[ 26.879905] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.879907] sda: sda1
[ 26.898756] sd 0:0:0:0: Attached scsi disk sda
[ 26.898880] SCSI device sdb: 240121728 512-byte hdwr sectors (122942 MB)
[ 26.898888] sdb: Write Protect is off
[ 26.898890] sdb: Mode Sense: 00 3a 00 00
[ 26.898901] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.898930] SCSI device sdb: 240121728 512-byte hdwr sectors (122942 MB)
[ 26.898937] sdb: Write Protect is off
[ 26.898939] sdb: Mode Sense: 00 3a 00 00
[ 26.898950] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 26.898952] sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
[ 26.938486] sd 1:0:0:0: Attached scsi disk sdb
[ 26.942493] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 26.942511] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 27.239155] Attempting manual resume
[ 27.239159] swsusp: Resume From Partition 8:21
[ 27.239161] PM: Checking swsusp image.
[ 27.239265] PM: Resume from disk failed.
[ 27.261143] kjournald starting. Commit interval 5 seconds
[ 27.261153] EXT3-fs: mounted filesystem with ordered data mode.
[ 27.387977] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:0a.0
[ 27.388354] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[ 27.388363] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 20
[ 27.438358] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
[ 27.438361] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 16
[ 27.438369] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 27.438372] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 27.438394] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 27.438405] ohci_hcd 0000:00:02.0: irq 16, io mem 0xf4001000
[ 27.438472] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[f3014000-f30147ff] Max Packet=[4096] IR/IT contexts=[4/8]
[ 27.497401] usb usb2: configuration #1 chosen from 1 choice
[ 27.497425] hub 2-0:1.0: USB hub found
[ 27.497434] hub 2-0:1.0: 10 ports detected
[ 27.603353] NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
[ 27.603371] NFORCE-CK804: chipset revision 242
[ 27.603374] NFORCE-CK804: not 100% native mode: will probe irqs later
[ 27.603379] NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
[ 27.603386] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[ 27.603395] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[ 27.603401] Probing IDE interface ide0...
[ 27.894749] hda: ST3120026A, ATA DISK drive
[ 27.910647] usb 2-7: new full speed USB device using ohci_hcd and address 2
[ 28.115346] usb 2-7: configuration #1 chosen from 1 choice
[ 28.178269] hdb: ST380021A, ATA DISK drive
[ 28.239058] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 28.245259] Probing IDE interface ide1...
[ 28.713433] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00148556003b1598]
[ 28.984918] hdc: _NEC DVD_RW ND-3551A, ATAPI CD/DVD-ROM drive
[ 29.771604] hdd: LITE-ON DVD SOHD-167T, ATAPI CD/DVD-ROM drive
[ 29.831901] ide1 at 0x170-0x177,0x376 on irq 15
[ 35.102801] NET: Registered protocol family 17
[ 35.359612] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 35.369929] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 35.684463] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[ 35.684490] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40
[ 35.767075] input: PC Speaker as /class/input/input2
[ 35.951018] parport: PnPBIOS parport detected.
[ 35.951058] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 36.143960] hda: max request size: 512KiB
[ 36.228717] hda: Host Protected Area detected.
[ 36.228719] current capacity is 234439535 sectors (120033 MB)
[ 36.228721] native capacity is 234441648 sectors (120034 MB)
[ 36.316621] hda: Host Protected Area disabled.
[ 36.316626] hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
[ 36.331513] hda: cache flushes supported
[ 36.331551] hda:<7>irda_init()
[ 36.343248] NET: Registered protocol family 23
[ 36.365638] Linux video capture interface: v2.00
[ 36.409944] hda1 hda2
[ 36.410700] hdb: max request size: 128KiB
[ 36.413514] hdb: Host Protected Area detected.
[ 36.413516] current capacity is 156299375 sectors (80025 MB)
[ 36.413518] native capacity is 156301488 sectors (80026 MB)
[ 36.417820] cx2388x v4l2 driver version 0.0.6 loaded
[ 36.417872] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 20
[ 36.417914] CORE cx88[0]: subsystem: 107d:6611, board: Leadtek Winfast 2000XP Expert [card=5,autodetected]
[ 36.417917] TV tuner 44 at 0x1fe, Radio tuner -1 at 0x1fe
[ 36.454654] hdb: Host Protected Area disabled.
[ 36.454660] hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 36.454665] hdb: cache flushes not supported
[ 36.454699] hdb: hdb1 hdb2
[ 36.523034] b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
[ 36.578488] cx88[0]: Leadtek Winfast 2000XP Expert config: tuner=38, eeprom[0]=0x01
[ 36.581623] input: ImPS/2 Generic Wheel Mouse as /class/input/input3
[ 36.598864] input: cx88 IR (Leadtek Winfast 2000XP as /class/input/input4
[ 36.598898] cx88[0]/0: found at 0000:01:06.0, rev: 5, irq: 20, latency: 32, mmio: 0xf2000000
[ 36.605859] hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 36.605868] Uniform CD-ROM driver Revision: 3.20
[ 36.608248] hdd: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33)
[ 36.724426] tuner 2-0043: chip found @ 0x86 (cx88[0])
[ 36.724451] tda9887 2-0043: tda988[5/6/7] found @ 0x43 (tuner)
[ 36.726948] tuner 2-0060: All bytes are equal. It is not a TEA5767
[ 36.726951] tuner 2-0060: chip found @ 0xc0 (cx88[0])
[ 36.726965] tuner 2-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
[ 36.726968] tuner 2-0060: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
[ 36.739245] cx88[0]/0: registered device video0 [v4l2]
[ 36.739273] cx88[0]/0: registered device vbi0
[ 36.739296] cx88[0]/0: registered device radio0
[ 36.740848] flexcop-pci: will use the HW PID filter.
[ 36.740852] flexcop-pci: card revision 2
[ 36.741118] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
[ 36.741127] ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 21
[ 36.759962] DVB: registering new adapter (FlexCop Digital TV device).
[ 36.761460] b2c2-flexcop: MAC address = 00:d0:d7:02:bf:78
[ 36.833663] ubuntu/media/gspcav1/gspca_core.c: USB SPCA5XX camera found.(SPCA561A)
[ 36.848775] usbcore: registered new interface driver gspca
[ 36.848780] ubuntu/media/gspcav1/gspca_core.c: gspca driver 01.00.12 registered
[ 37.011605] b2c2-flexcop: found the stv0299 at i2c address: 0x68
[ 37.011610] DVB: registering frontend 0 (ST STV0299 DVB-S)...
[ 37.011668] b2c2-flexcop: initialization of 'Sky2PC/SkyStar 2 DVB-S' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
[ 37.020227] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[ 37.020237] ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 22
[ 37.020257] snd-ca0106: Model 100a Rev 00000000 Serial 100a1102
[ 37.446067] fuse init (API version 7.
[ 37.484012] lp0: using parport0 (interrupt-driven).
[ 37.537169] usbcore: registered new interface driver cxacru
[ 37.571028] PPP generic driver version 2.4.2
[ 37.608575] bttv: driver version 0.9.16 loaded
[ 37.608580] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 37.649908] Adding 522072k swap on /dev/disk/by-uuid/599a3ea3-09ff-4082-a86f-ba6862701ae8. Priority:-1 extents:1 across:522072k
[ 37.922538] EXT3 FS on sdb2, internal journal
[ 39.083577] NET: Registered protocol family 10
[ 39.083663] lo: Disabled Privacy Extensions
[ 40.972557] kjournald starting. Commit interval 5 seconds
[ 40.972641] EXT3 FS on sdb3, internal journal
[ 40.972645] EXT3-fs: mounted filesystem with ordered data mode.
[ 46.646034] No dock devices found.
[ 46.679182] Using specific hotkey driver
[ 46.786844] ibm_acpi: ec object not found
[ 46.841986] input: Power Button (FF) as /class/input/input5
[ 46.845564] ACPI: Power Button (FF) [PWRF]
[ 46.878049] input: Power Button (CM) as /class/input/input6
[ 46.881657] ACPI: Power Button (CM) [PWRB]
[ 46.966995] pcc_acpi: loading...
[ 47.119445] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (version 2.00.00)
[ 47.119487] powernow-k8: invalid freq entries 3900000 kHz vs. 65535000 kHz
[ 47.119490] powernow-k8: invalid freq entries 3900000 kHz vs. 65535000 kHz
[ 47.119493] powernow-k8: invalid freq entries 3900000 kHz vs. 65535000 kHz
[ 47.119495] powernow-k8: invalid freq entries 3900000 kHz vs. 65535000 kHz
[ 47.119498] powernow-k8: 0 : fid 0xa (1800 MHz), vid 0x6
[ 47.119501] powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
[ 49.702197] eth0: no IPv6 routers present
[ 52.255131] Linux agpgart interface v0.102 (c) Dave Jones
[ 52.303267] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 52.308890] [fglrx] Maximum main memory to use for locked dma buffers: 929 MBytes.
[ 52.309162] [fglrx] module loaded - fglrx 8.34.8 [Feb 20 2007] on minor 0
[ 52.319376] ACPI: PCI Interrupt 0000:05:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 20
[ 53.325951] ppdev: user-space parallel port driver
[ 54.370349] [fglrx] total GART = 130023424
[ 54.370355] [fglrx] free GART = 114032640
[ 54.370358] [fglrx] max single GART = 114032640
[ 54.370360] [fglrx] total LFB = 268304384
[ 54.370362] [fglrx] free LFB = 256765952
[ 54.370364] [fglrx] max single LFB = 256765952
[ 54.370366] [fglrx] total Inv = 0
[ 54.370368] [fglrx] free Inv = 0
[ 54.370369] [fglrx] max single Inv = 0
[ 54.370371] [fglrx] total TIM = 0
[ 55.241280] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[ 55.241285] apm: overridden by ACPI.
[ 55.401713] Bluetooth: Core ver 2.11
[ 55.401765] NET: Registered protocol family 31
[ 55.401767] Bluetooth: HCI device and connection manager initialized
[ 55.401770] Bluetooth: HCI socket layer initialized
[ 55.441827] Bluetooth: L2CAP ver 2.8
[ 55.441831] Bluetooth: L2CAP socket layer initialized
[ 55.511726] Bluetooth: RFCOMM socket layer initialized
[ 55.511737] Bluetooth: RFCOMM TTY layer initialized
[ 55.511739] Bluetooth: RFCOMM ver 1.8
[ 38.108000] Time: acpi_pm clocksource has been installed.
[ 46.576000] eth0: no IPv6 routers present
Problem ze sterownikami. (5)