Nowe posty

xx Dystrybucja pod HP Omen (6)
2024-03-27, 23:30:08
xx [Poradnik] Wyszukiwanie Sterowników (2)
2024-03-27, 21:08:23
lamp Problem z Linux Lite po instalacji (0)
2024-03-27, 19:50:30
xx Ile pingwinów? (1)
2024-03-27, 08:59:24
xx konfiguracja pale moon (0)
2024-03-24, 21:53:42
xx Plasma 6 w Neonie ssie trochę mniej ... (10)
2024-03-23, 02:38:11
xx problem z instalacja sterowników do karty sieciowej (3)
2024-03-18, 18:10:16
xx Plik abc.001 (1)
2024-03-17, 17:48:27
xx Zlecę dopracowanie programu w MatLab (0)
2024-03-13, 15:28:40
xx Linux Mint 21.3 XFCE brak dźwieku po paru minutach (karta muzyczna zintegrowana) (5)
2024-03-12, 23:07:01

Autor Wątek: Nie moge załadowac środowiska graficznego  (Przeczytany 8058 razy)

stasiek1991

  • Gość
Nie moge załadowac środowiska graficznego
« dnia: 2006-01-08, 12:46:28 »
Witam
Jestem nowy, Linuxa mam od dzisiejszego ranka;p(Aurox 9) Pojawił sie problem. Mianowicie mam karte MINT SOUND CARD 3D, podlaczone do niej kino 5.1 i niby wszystko okej ale dzwięk slychać tylko z 2 głoścników. Ściągnąłem sterowniki ze strony minta ale nie wiem jak je zainstalowac. W pliku Readme jest cos takiego:

Audio driver for CM8338/CM8738 chips by Chen-Li Tien





HARDWARE SUPPORTED

================================================================================

C-Media CMI8338

C-Media CMI8738

On-board C-Media chips





WHAT\\'S NEW

================================================================================



1. Support modem interface for 8738. (select in kernel configuration)

2. Enable S/PDIF-in to S/PDIF-out (S/PDIF loop).

3. Enable 4 channels analog duplicate mode on 3 jack or 4 jack

configurateion.

4. Enable joystick support. (joystick driver needed)





STEPS TO BUILD DRIVER

================================================================================



1. Backup the Config.in and Makefile in the sound driver directory

(/usr/src/linux/driver/sound).

The Configure.help provide help when you config driver in step

4, please backup the original one (/usr/src/linux/Document) and

copy this file.

The cmpci is document for the driver in detail, please copy it

to /usr/src/linux/Document/sound so you can refer it. Backup if

there is already one.



2. Extract the tar file by \\'tar xvzf cmpci-xx.tar.gz\\' in the above

directory.



3. Change directory to /usr/src/linux



4. Config cm8338 driver by \\'make menuconfig\\', \\'make config\\' or

\\'make xconfig\\' command.



5. Please select Sound Card (CONFIG_SOUND=m) support and CMPCI

driver (CONFIG_SOUND_CMPCI=m) as modules. Resident mode not tested.

For driver option, please refer \\'DRIVER PARAMETER\\'



6. Compile the kernel if necessary.



7. Compile the modules by \\'make modules\\'.



8. Install the modules by \\'make modules_install\\'





INSTALL DRIVER

================================================================================



1. Before first time to run the driver, create module dependency by

\\'depmod -a\\'



2. To install the driver manually, enter \\'modprobe cmpci\\'.



3. Driver installation for various distributions:



a. Slackware 4.0

Add the \\'modprobe cmpci\\' command in your /etc/rc.d/rc.modules

file.so you can start the driver automatically each time booting.



b. Caldera OpenLinux 2.2

Use LISA to load the cmpci module.



c. RedHat 6.0 and S.u.S.E. 6.1

Add following command in /etc/conf.modules:



alias sound cmpci



also visit http://www.cmedia.com.tw for installation instruction.



DRIVER PARAMETER

================================================================================



Some functions for the cm8738 can be configured in Kernel Configuration

or modules parameters. Set these parameters to 1 to enable.



spdif_loop: Enable S/PDIF loop, this route S/PDIF-in to S/PDIF-out

directly.

four_ch: Enable 4 channels mode, rear-out or line-in will output

the same as line-out.

rear_out: Enable this if you have independent rear-out jacket on

your sound card, otherwise line-in will be used as

rear-out.

modem: You will need to set this parameter if you want to use

the HSP modem. You need install the pctel.o, the modem

driver itself.

joystich: Enable joystick. You will need to install Linux joystick

driver.

Może mi ktoś powiedzieć po polsku i w prosty sposób co mam z tym zrobić?

Bardzo proszę i z góry dziekuje za pomoc, Stasiu

chmooreck

  • Gość
Nie moge załadowac środowiska graficznego
« Odpowiedź #1 dnia: 2006-01-08, 13:24:10 »
alsamixer pod konsola...

sadowski5

  • Gość
Nie moge załadowac środowiska graficznego
« Odpowiedź #2 dnia: 2006-01-08, 11:02:41 »
Witam wszystkich mam mały problem .Zainstalowałem Madrive 2005 ,instalacja zakonczyła sie pozytywnie ale gdy chciałem uruchomic system to uruchamia sie konsola ,a nie srodowisko graficzne .Jak uruchomic środowisko graficzne ?? z góry dziekuje za pomoc:)

devilan

  • Gość
Nie moge załadowac środowiska graficznego
« Odpowiedź #3 dnia: 2006-01-08, 12:06:51 »
2006-01-08 11:02:41 sadowski5 napisał:

> Witam wszystkich mam mały problem .Zainstalowałem Madrive 2005 ,instalacja zakonczyła sie
 > pozytywnie ale gdy chciałem uruchomic system to uruchamia sie konsola ,a nie srodowisko
 > graficzne .Jak uruchomic środowisko graficzne ?? z góry dziekuje za pomoc:)

Zaloguj sie pod konsola... i wpisz:
startx

jesli sie uruchomi tryb graficzny, to znaczy ze wszystko jest ok, tylko musisz ustawic w pliku /etc/inittab odpowiedni defaultrunlevel
Pewno tez da sie to z srodowiska graficznego ustawic, ale nie wiem jak bo mam Slackware :)