Witam
Mam problem w części podobny do "amazis'a". Korzystam z KDE 3.4 na Slackware 10.2 kernel 2.6.14.3. X zawieszaja sie w nieoczekiwanych momentach, wcześniej zawis był kompletny i totalna utrata panowania nad system, teraz wylatuja tylko X'y ale konsola jeszcze śmiga, ale nie ma możliwości ponownego załadowania (NAWET PO REBOOTcie) pomaga całkowite wyłączenie i start od zera. Zwiechy są w jakimś stopniu powiazane z siecią bo dopóki nie korzystalem z sieci nigdy sie nie pojawiały. Wyglada to tak ze najpierw pojawiają sie małe prążki na nagłówkach okien i na pasku kursora w rozwijanych menu, po jakims czasie cały ekran dostaje pionowych kolorowych prążków (nie zawsze zawis jest poprzedzony prążkami na oknach). Dzieje sie to na kazdej przegladarce od firefoxów po mozille i konquerora. Sprawdzilem juz 3 sieciówki i problem nadal ten sam, pamieci przeskanowane memtestem i dysk czyściutki.
Aby nie rozwodzić sie na czym pracuje załączam zrzut dmesg'a i lshw'a
###################################################
description: Desktop Computer
vendor: Compaq
serial: xxx
width: 32 bits
capabilities: smbios-2.3 dmi-2.3
configuration: chassis=desktop
*-core
description: Motherboard
product: 055Ch
vendor: Compaq
physical id: 0
serial: xxx
*-firmware
description: BIOS
vendor: Compaq
physical id: 1
version: 686J1 v1.10 (08/12/1999)
size: 128KB
capacity: 448KB
capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect edd int13floppy360 int13floppy1200 int13floppy720 int5printscreen int9keyboard int14serial int17printer acpi usb agp ls120boot biosbootspecification
*-cpu
description: CPU
product: Celeron (Mendocino)
vendor: Intel Corp.
physical id: 5
bus info: cpu@0
version: 6.6.5
slot: XU1
size: 500MHz
capacity: 500MHz
width: 32 bits
clock: 66MHz
capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov pat pse36 mmx fxsr
*-cache:0
description: L1 cache
physical id: 6
slot: Internal L1 Cache
size: 32KB
capacity: 32KB
capabilities: burst internal write-through
*-cache:1
description: L2 cache
physical id: 7
slot: Cache L2
size: 128KB
capacity: 4MB
capabilities: burst internal write-through
*-memory:0
description: System Memory
physical id: 1c
slot: System board or motherboard
capacity: 512MB
*-bank:0
description: DIMM SDRAM Synchronous 100 MHz (10.0 ns)
physical id: 0
slot: XMM1
size: 128MB
width: 64 bits
clock: 100MHz (10ns)
*-bank:1
description: DIMM SDRAM Synchronous 100 MHz (10.0 ns)
physical id: 1
slot: XMM2
size: 128MB
width: 64 bits
clock: 100MHz (10ns)
*-memory:1 UNCLAIMED
description: Flash Memory
physical id: 1d
slot: System board or motherboard
capacity: 512KB
*-bank UNCLAIMED
description: Chip FLASH
physical id: 0
slot: XU15
size: 512KB
width: 4 bits
*-memory:2 UNCLAIMED
physical id: 0
*-memory:3 UNCLAIMED
physical id: 2
*-pci
description: Host bridge
product: 82810 DC-100 GMCH [Graphics Memory Controller Hub]
vendor: Intel Corporation
physical id: 100
bus info: pci@00:00.0
version: 02
width: 32 bits
clock: 33MHz
*-display
description: VGA compatible controller
product: 82810 DC-100 CGC [Chipset Graphics Controller]
vendor: Intel Corporation
physical id: 1
bus info: pci@00:01.0
logical name: /dev/fb0
version: 02
size: 64MB
width: 32 bits
clock: 66MHz
capabilities: vga bus_master cap_list fb accelerated
configuration: depth=8 driver=i810fb frequency=75.08Hz mode=1024x768 visual=pseudocolor xres=1024 yres=768
resources: iomemory:44000000-47ffffff iomemory:40300000-4037ffff irq:11
*-pci
description: PCI bridge
product: 82801AA PCI Bridge
vendor: Intel Corporation
physical id: 1e
bus info: pci@00:1e.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: pci normal_decode bus_master
*-network
description: Ethernet interface
product: RTL8139 Ethernet
vendor: D-Link System Inc
physical id: 8
bus info: pci@01:08.0
logical name: eth0
version: 10
serial: xxx
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegociation
configuration: autonegociation=on broadcast=yes driver=8139too driverversion=0.9.27 duplex=full ip=xxx.xxx.xxx.xxx link=yes multicast=yes port=MII speed=100MB/s
resources: ioport:1000-10ff iomemory:40000000-400000ff irq:11
*-isa UNCLAIMED
description: ISA bridge
product: 82801AA ISA Bridge (LPC)
vendor: Intel Corporation
physical id: 1f
bus info: pci@00:1f.0
version: 01
width: 32 bits
clock: 33MHz
capabilities: isa bus_master
*-ide
description: IDE interface
product: 82801AA IDE
vendor: Intel Corporation
physical id: 1f.1
bus info: pci@00:1f.1
version: 01
width: 32 bits
clock: 33MHz
capabilities: ide bus_master
configuration: driver=PIIX_IDE
resources: ioport:2460-246f
*-ide:0
description: IDE Channel 0
physical id: 0
bus info: ide@0
logical name: ide0
clock: 33MHz
*-disk
description: ATA Disk
product: FUJITSU MPD3084AT
vendor: Fujitsu
physical id: 0
bus info: ide@0.0
logical name: /dev/hda
version: DD-03-47
serial: xxx
size: 8062MB
capacity: 8062MB
capabilities: ata dma lba iordy smart security pm apm
configuration: apm=off mode=udma2 smart=on
*-ide:1
description: IDE Channel 1
physical id: 1
bus info: ide@1
logical name: ide1
clock: 33MHz
*-cdrom
description: DVD reader
product: HL-DT-STDVD-ROM GDR8163B
physical id: 0
bus info: ide@1.0
logical name: /dev/hdc
version: 0L14
capabilities: packet atapi cdrom removable nonmagnetic dma lba iordy pm audio dvd
configuration: mode=udma2
*-usb
description: USB Controller
product: 82801AA USB
vendor: Intel Corporation
physical id: 1f.2
bus info: pci@00:1f.2
version: 01
width: 32 bits
clock: 33MHz
capabilities: uhci bus_master
configuration: driver=uhci_hcd
resources: ioport:2440-245f irq:11
*-multimedia
description: Multimedia audio controller
product: 82801AA AC'97 Audio
vendor: Intel Corporation
physical id: 1f.5
bus info: pci@00:1f.5
version: 01
width: 32 bits
clock: 33MHz
capabilities: bus_master
configuration: driver=Intel ICH
resources: ioport:2000-20ff ioport:2400-243f irq:11
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: dummy0
serial: xxx
capabilities: ethernet physical
configuration: broadcast=yes
###################################################
Linux version 2.6.14.3 (gcc version 3.3.6) #4 PREEMPT Fri Dec 16 02:31:26 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000ff00000 (usable)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65280
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61184 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 COMPAQ ) @ 0x000e0010
ACPI: RSDT (v001 COMPAQ CPQB13A 0x19990812 0x00000000) @ 0x000e0080
ACPI: FADT (v001 COMPAQ WHITNEY 0x00000001 0x00000000) @ 0x000e00cc
ACPI: SSDT (v001 COMPAQ VILLTBL1 0x00000001 MSFT 0x0100000b) @ 0x000e098a
ACPI: SSDT (v001 COMPAQ PNP_PRSS 0x00000001 MSFT 0x0100000b) @ 0x000e164d
ACPI: SSDT (v001 COMPAQ S1 0x00000001 MSFT 0x0100000b) @ 0x000e2a40
ACPI: DSDT (v001 COMPAQ DSDT 0x00000001 MSFT 0x0100000b) @ 0x00000000
Allocating PCI resources starting at 10000000 (gap: 0ff00000:efc80000)
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=midi_fb ro root=301 video=i810fb:vram:4,xres:1024,yres:768,bpp:8,hsync1:30,hsync2:55,vsync1:50,vsync2:85,accel,mtrr
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 498.575 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 254296k/261120k available (2921k kernel code, 6372k reserved, 842k data, 164k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 999.15 BogoMIPS (lpj=1998316)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Celeron (Mendocino) stepping 05
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0800)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xecb53, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [_SB_.PCI0] bus is 0
Boot video device is 0000:00:01.0
PCI quirk: region f800-f87f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region fa00-fa3f claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0c: ioport range 0x400-0x41f has been reserved
pnp: 00:0c: ioport range 0x420-0x43f has been reserved
pnp: 00:0c: ioport range 0x440-0x45f has been reserved
pnp: 00:0c: ioport range 0x460-0x47f could not be reserved
pnp: 00:0c: ioport range 0xf800-0xf81f could not be reserved
pnp: 00:0c: ioport range 0xf820-0xf83f could not be reserved
pnp: 00:0c: ioport range 0xf840-0xf85f has been reserved
pnp: 00:0c: ioport range 0xf860-0xf87f has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.0
PCI: Bridge: 0000:00:1e.0
IO window: 1000-1fff
MEM window: 40000000-402fffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.24 [Flags: R/W DEBUG].
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PBTN]
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i810 DC100 Chipset.
agpgart: detected 4MB dedicated video ram.
agpgart: AGP aperture is 64M @ 0x44000000
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized i810 1.4.0 20030605 on minor 0:
ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
i810-i2c: Probe DDC1 Bus
i810-i2c: I2C Transfer successful
i810fb_init_pci: DDC probe successful
ringbuffer lockup!!!
IIR : 0x0000
EIR : 0x0000
PGTBL_ER: 0x0000
IPEIR : 0x0001
IPEHR : 0x0000
Console: switching to colour frame buffer device 128x48
I810FB: fb0 : Intel(R) 810-DC100 Framebuffer Device v0.9.0
I810FB: Video RAM : 4096K
I810FB: Monitor : H: 30-92 KHz V: 50-150 Hz
I810FB: Mode : 1024x768-8bpp@75Hz
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
pnp: Device 00:08 activated.
pnp: Device 00:09 activated.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0x1000, xxx, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH: IDE controller at PCI slot 0000:00:1f.1
ICH: chipset revision 1
ICH: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2460-0x2467, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2468-0x246f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MPD3084AT, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 16511951 sectors (8454 MB) w/512KiB Cache, CHS=16380/16/63, UDMA(33)
hda: cache flushes not supported
hda: hda1
hdc: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
usbmon: debugfs is not available
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 11, io base 0x00002440
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1f.5
-> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.5 to 64
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
intel8x0_measure_ac97_clock: measured 54262 usecs
intel8x0: clocking to 48000
ALSA device list:
#0: Intel 82801AA-ICH with AD1881 at 0x2000, irq 11
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
ip_conntrack version 2.3 (2040 buckets, 16320 max) - 216 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/
arp_tables: (C) 2002 David S. Miller
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: journal-1153: found in header: first_unflushed_offset 7232, last_flushed_trans_id 78101
ReiserFS: hda1: journal-1206: Starting replay from offset 335445535759424, trans_id 0
ReiserFS: hda1: journal-1299: Setting newest_mount_id to 145
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 164k freed
Adding 262136k swap on /pagefile.swp. Priority:-1 extents:3 across:262144k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
##################################################
mam nadzieje ze zalaczniki okaza sie pomocne a nie beda stanowic spamu
Pozdrawiam i czekam na jakies sugestie, solucje