2005-11-24 21:27:38 pretoriusz napisał:
> Wiem, ze plik sie nazywa inux-fbdev-kernel-src_20050527.tgz i pobralem go ze strony
>
http://www.viaarena.com/default.aspx?PageID=420&OSID=25&CatID=2580&SubCatID=101 Mam
> go teraz na dysku i moge rozakowac programem ARK jest tam plik redme.txt ale nic z niego nie
> rozumiem pisze tam:
> ---------------------------------------------------------------------------
>
> VIA Integration Graphic Chip Console Framebuffer Driver
> Copyright 2005 VIA Technologies, Inc. All Rights Reserved.
>
> ---------------------------------------------------------------------------
> Platform
>
> The console framebuffer driver is for Graphics chips of
> VIA UniChrome Family (CLE266, KM400, KN400, K8M800, K8N800, PM800, PN800, CN400).
>
> ---------------------------------------------------------------------------
> Driver features
>
> Device: CRT, TV
> Support Mode: CRT: 640x480(60,75,85,100,120Hz), 720x480(60Hz),
> 720x576(60Hz), 800x600(60,75,85,100,120Hz),
> 848x480(60Hz), 856x480(60Hz), 1024x512(60Hz),
> 1024x768(60,75,85,100Hz), 1152x864(75Hz),
> 1280x768(60Hz), 1280x960(60Hz), 1280x1024(60,75,85Hz),
> 1440x1050(60Hz), 1600x1200(60,75Hz),
> 1280x720(60Hz), 1920x1080(60Hz), 1400x1050(60Hz), 800x480(60Hz)
> TV: VT1622, VT1622A, VT1623 (640x480, 800x600, 1024x768, 720x480, 720x576,
> 848x480)
> VT1625 (640x480, 800x600, 1024x768, 720x480, 720x576, 1280x720(HDTV),
> 1920x1080(HDTV))
>
> color depth : 8 bpp, 16 bpp, 32 bpp
> TV encoder : VIA VT1622, VT1622A, VT1623, VT1625
> TV output : VT1622 (Composite, S-Video, Composite+S-Video, YCBCR)
> VT1622A ,VT1623 (Composite, S-Video, Composite+S-Video, RGB, YCBCR, SDTV_RGB,
> SDTV_YPBPR)
> VT1625 (Composite, S-Video, Composite+S-Video, RGB, YCBCR , SDTV_RGB,
> SDTV_YPBPR, HDTV_RGB_720P, HDTV_YPBPR_720P, HDTV_RGB_1080I, HDTV_YPBPR_1080I)
> TV type : NTSC,PAL
> Support TV overscan display
> Support 2D hardware accelerator for kernel 2.6.
>
> ---------------------------------------------------------------------------
> Building viafb as a module. (for Linux kernel 2.4)
> Make sure you have the kernel sources in /usr/src/linux-2.4.
> Change to the viafb directory, and then following below steps:
> Step 1: change to folder /usr/src/linux-2.4.
> # cd /usr/src/linux-2.4.
> The linux-2.4 directory depend on your kernel version, so if your kernel version
> is
> 2.4.18-3, you should type "/usr/src/linux-2.4.18-3".
> Step 2: copy viafb folder in current directory.
> # cp -rf .../viafb ./
> Step 3: change to viafb directory
> # cd /viafb
> Step 4: Clear all object file.
> # make clean
> Step 5: Make source code
> # make
> Note that if no any error, this step will be produced an object file
> "viafb.o".
> Step 6: Install viafb.o framebuffer driver
> # make install
>
> ---------------------------------------------------------------------------
> Using the viafb module. (for Linux kernel 2.4)
>
> Start viafb with default settings,
> #modprobe viafb
>
> Start viafb with with user options,
> #modprobe viafb mode=800x600 bpp=16 refresh=60 TV_ON=1 tv_system=1 tv_level=1
> tv_out_signal=4 mode1=1024x768 bpp1=16 refresh1=60 SAMM_ON=1
>
> mode :
> 640x480 (default)
> 720x480
> 800x600
> 1024x768
> ......
>
> bpp :
> 8, 16, 32 (default : 32)
>
> refresh :
> 60, 75, 85, 100, 120 (default : 60)
>
> CRT_ON:
> 0 : CRT disable
> 1 : CRT enable (default)
>
> TV_ON :
> 0 : TV disable (default)
> 1 : TV enable
>
> tv_system :
> 0 : none
> 1 : NTSC (default)
> 2 : PAL
>
> tv_level :
> VT1622, VT1622A, VT1623
> 0 : underscan (default)
> 1 : fitscan (close to fit Industry TV Screen)
> 2 : overscan
> Other TV Encoders
> 0 : underscan (default)
> 1 : overscan
>
> tv_out_signal:
> 1: Composite
> 2: S-Video
> 3: Composite+S-Video (default)
> 4: RGB
> 5: YCBCR (or component)
> 6: RGB+Composite
> 7: YCBCR+Composite
> 8. SDTV_RGB (480P, 576P)
> 9. SDTV_YPBPR (480P, 576P)
> 10. HDTV_RGB (720P)
> 11. HDTV_YPBPR (720P)
> 12. HDTV_RGB (1080I)
> 13. HDTV_YPBPR (1080I)
>
> tv_dedotcrawl:
> 0: Disable DeDotCrawl Function (default)
> 1: Enable DeFotCrawl Function
> Note that the DeDotCrawl work under NTSC and composite outputting condition,
> other
> conditions don't support this function.
>
> tv_brightness:
> 0 ~ 255 : To set TV output brightness
>
> tv_contrast:
> 0 ~ 255 : To set TV output contrast
>
> tv_saturation:
> 0 ~ 65535 : To set TV output saturation
>
> tv_tint:
> 0 ~ 2047 : To set TV output tint
> Note: Different TV encoder have different default values of TV color features
> including brightness, contrast, saturation, and tint.
>
> DVI_ON:
> 0 : DVI disable
> 1 : DVI enable (default)
>
> LCD_ON :
> 0 : LCD disable (default)
> 1 : LCD enable
>
> lcd_dsp_method:
> 0 : expandsion (default)
> 1 : centering
>
> lcd_panel_id:
> 0 : Resolution: 640x480, Channel: single, Dithering: Enable
> 1 : Resolution: 800x600, Channel: single, Dithering: Enable
> 2 : Resolution: 1024x768, Channel: single, Dithering: Enable (default)
> 3 : Resolution: 1280x768, Channel: single, Dithering: Enable
> 4 : Resolution: 1280x1024, Channel: dual, Dithering: Enable
> 5 : Resolution: 1400x1050, Channel: dual, Dithering: Enable
> 6 : Resolution: 1600x1200, Channel: dual, Dithering: Enable
> 9 : Resolution: 1024x768, Channel: dual, Dithering: Enable
> 10: Resolution: 1024x768, Channel: single, Dithering: Disable
> 11: Resolution: 1024x768, Channel: dual, Dithering: Disable
> 12: Resolution: 1280x768, Channel: single, Dithering: Disable
> 13: Resolution: 1280x1024, Channel: dual, Dithering: Disable
> 14: Resolution: 1400x1050, Channel: dual, Dithering: Disable
> 15: Resolution: 1600x1200, Channel: dual, Dithering: Disable
>
> accel: (only for kernel 2.6)
> 0 : No 2D Hardware Acceleration (default)
> 1 : 2D Hardware Acceleration
>
> SAMM_ON:
> 0 : SAMM_ON disable (default)
> 1 : SAMM_ON enable
>
> mode1 :(secondary display device)
> 640x480 (default)
> 720x480
> 800x600
> 1024x768
> ......
>
> bpp1 :(secondary display device)
> 8, 16, 32 (default : 32)
>
> refresh1 :(secondary display device)
> 60, 75, 85, 100, 120 (default : 60)
>
>
> Note :
> 1. If TV is enabled, the refresh rate will be bound to TV type (NTSC:60Hz, PAL:50Hz).
> 2. CRT may not display properly for simultaneous CRT & TV display at
> the "640x480" PAL mode with TV overscan enabled.
> 3. When SAMM is enable, mode and mode1,bpp and bpp1,refresh and refresh1 can
> be different.
>
> ---------------------------------------------------------------------------
> Configure viafb options with "fbset" tool
>
> "fbset" is an inbox utility of Linux.
>
> 1. Inquire current viafb information, type,
> # fbset -i
>
> 2. Set various resolutions and refresh rates,
> # fbset
> example,
> # fbset "1024x768-75"
>
> Check the file "/etc/fb.modes" to find display modes available.
>
> 3. Set the color depth,
> # fbset -depth
> example,
> # fbset -depth 16
>
> ---------------------------------------------------------------------------
> Building and loading viafb device driver for Linux kernel 2.6
> ---------------------------------------------------------------------------
> Building fbcon console module.
> Step 1: Change to folder /usr/src/linux-2.6.
> # cd /usr/src/linux-2.6.
> The linux-2.6 directory depend on your kernel version, so if your kernel version
> is
> 2.6.5-1.358, you should type "/usr/src/linux-2.6.5-1.358".
> Step 2: Configuring the kernel module
> # make menuconfig
> Step 3: Select fbcon item to module.
> -> Device Drivers->Graphics support->Console display driver support->
> Framebuffer Console support
> Step 4: Save the current setting and quit.
> Step 5: Make fbcon module.
> # make modules
> Note that if no any error, this step will be produced "fbcon.ko" in
> /usr/src/linux-2.6./drivers/video/console folder.
> Step 6: Copy fbcon.ko to lib folder.
> # cp /usr/src/linux-2.6./drivers/video/console/fbcon.ko
> /lib/modules/2.6./kernel/drivers/video
>
> ---------------------------------------------------------------------------
> Building viafb as a module. (for Linux kernel 2.6)
> Make sure you have the kernel sources in /usr/src/linux-2.6.
> Change to the viafb directory, and then following below steps:
>
> Step 1: change to folder /usr/src/linux-2.6.
> # cd /usr/src/linux-2.6.
> The linux-2.6 directory depend on your kernel version, so if your kernel version
> is
> 2.6.5-1.358, you should type "/usr/src/linux-2.6.5-1.358".
> Step 2: copy viafb folder in current directory.
> # cp -rf .../viafb ./
> Step 3: change to viafb directory
> # cd /viafb
> Step 4: Clear all object file.
> # make clean
> Step 5: Make source code
> # make
> Note that if no any error, this step will be produced an object file
> "viafb.ko".
> Step 6: Install viafb.ko framebuffer driver
> # make install
>
> ---------------------------------------------------------------------------
> Using the viafb module. (for Linux kernel 2.6)
> If you want to modprobe viafb.ko into kernel and change the display mode in Linux kernel
> 2.6 and later versions,
> you need a framebuffer device driver(viafb.ko) and a framebuffer console module(fbcon.ko).
> Modprobing viafb will not change the display mode until you modprobe fbcon.
> You can see the related steps below.
>
> Step 1: Start viafb with default settings.
> # modprobe viafb
> Note that you can see the other options from "Using the viafb module. (for
> Linux kernel 2.4)" section.
> Step 2: Modprope fbcon.
> # modprobe fbcon
>
>
> To chyba wszystko co tam pisze a ja i tak nadal nie wiem co mam zrobic prosze mi napisac po
> kolei wersja dla laika jak najszybciej ta kara VIA PN 800 zainstalowac w moim systemie Aurox
> 11.0
Jak se z Aurox nie radzisz to bym proponował Linux SuSe(Ł)10 PL ja na niego przeszłem on wykrywa automatycznie wszystkie sprzety jakie masz w kompie czy Laptopie a potem mozesz to dokładniej ustawić w ustawieniach.Ale z szukaniem tych sterowników zajmie ci czasu.Bo to tak jest jak byś przyjechał do domu po roku czasu i zaszło tam przemeblowanie i nie wiesz gdzie czego szukać.Ja też przyzwyczajony do WinXP i sie przekonałem że Linux Nie dla "Idiotów"klik klik i "Fertig" po polsku gotowe.Syn ma podobny laptop jak ty ale 2020 i na Debian i tam trzeba wszystko na piechote robić i nie automatycznie. I dałem sobie spokuj ,a SuSe to dla takich co Win w życiu tylko widzieli i chcą skosztować linux-a.Ale i on nie jest Tak łatwy jak sie wydawało dla mie też trzeba używać sarych komórek,bo to nowy system z którym trzeba sie zaznajomić.A zeby jakis program zainstalować to trzeba najwpierw ksiązkę dokładnie przeczytać a potem brać sie do instalki. Ale za to jaki stabilny i nie robi ci numerków ,ale za to masz numerki z instalacja .Ale jak raz zainstalujesz to chodzi i nie marudzi.A WIN dopiero zaczyna ci marudzić.Najlepiej mi sie podobają w SuSe te "ciasteczka"w przegladarce internetowej i zadnych reklam nie mam spokuj z nimi i spokojnie mozesz pracować ale mam nadzieję ze sprubujesz z SuSe i bedziesz zadowolony I kup se ksiązkę "Linux SuSe zaczynamy od podstaw" i wtedy kombinuj jak ci nie wychodzi bierz ksiązkę i czytaj a wtedy wyjdzie.Ja też jestem cieniutki w Linux jak ty!!!