Nowe posty

xx Dystrybucja pod HP Omen (6)
2024-03-27, 23:30:08
xx [Poradnik] Wyszukiwanie Sterowników (2)
2024-03-27, 21:08:23
lamp Problem z Linux Lite po instalacji (0)
2024-03-27, 19:50:30
xx Ile pingwinów? (1)
2024-03-27, 08:59:24
xx konfiguracja pale moon (0)
2024-03-24, 21:53:42
xx Plasma 6 w Neonie ssie trochę mniej ... (10)
2024-03-23, 02:38:11
xx problem z instalacja sterowników do karty sieciowej (3)
2024-03-18, 18:10:16
xx Plik abc.001 (1)
2024-03-17, 17:48:27
xx Zlecę dopracowanie programu w MatLab (0)
2024-03-13, 15:28:40
xx Linux Mint 21.3 XFCE brak dźwieku po paru minutach (karta muzyczna zintegrowana) (5)
2024-03-12, 23:07:01

Autor Wątek: Brak połączenia z siecią RHEL3 i HP integrity RX1620  (Przeczytany 4534 razy)

miniol87

  • Gość
Mam problem z podłączeniem się do neta. Wcześniej neta miałem, ale postanowiłem na nowo system postawić i po tym zabiegu już nie mogę odpalić neta. Siedzę nad tym od rana i już mi się pomysły skończyły.
Jestem laikiem więc być może chodzi o jakąś drobnostkę.

ifconfig wypluwa mi ip localhosta.

alvaro

  • Gość
Brak połączenia z siecią RHEL3 i HP integrity RX1620
« Odpowiedź #1 dnia: 2014-01-04, 19:06:38 »
Jak mniemam łączyłeś się z siecią przewodowo, tak?

Dobrze byłoby gdybyś jednak podzielił się wynikiem polecenia:
ifconfig
Poza tym przydałyby się informacje na temat urządzeń PCI:
lspci -nn -k
i ewentualnie USB:
lsusb
Dodatkowo możesz podać informacje na temat załadowanych modułów jądra:
lsmod
oraz jego wersję:
uname -r
Pomocne może okazać się także:
dmesg
Być może musisz zainstalować jakiś sterownik/firmware, ale bez powyższych informacji ciężko będzie cokolwiek stwierdzić.

Na koniec drobna uwaga - rozszerzone wsparcie (Extended Life Cycle) dla RHEL 3 kończy się w tym miesiącu. Wypadałoby już przygotować się do migracji na nowszą wersję lub inny system.

miniol87

  • Gość
Brak połączenia z siecią RHEL3 i HP integrity RX1620
« Odpowiedź #2 dnia: 2014-01-06, 16:13:59 »
Cytat: alvaro
Jak mniemam łączyłeś się z siecią przewodowo, tak?
Tak, przewodowo. Przez router (jeśli to ma jakieś znaczenie).
Cytat: alvaro
Dobrze byłoby gdybyś jednak podzielił się wynikiem polecenia:
ifconfig
[root@localhost root]# ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:212 errors:0 dropped:0 overruns:0 frame:0
          TX packets:212 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:16286 (15.9 Kb)  TX bytes:16286 (15.9 Kb)
Cytat: alvaro
Poza tym przydałyby się informacje na temat urządzeń PCI:
lspci -nn -k
[root@localhost root]# lspci -n
00:01.0 Class 0c03: 1033:0035 (rev 41)
00:01.1 Class 0c03: 1033:0035 (rev 41)
00:01.2 Class 0c03: 1033:00e0 (rev 02)
00:02.0 Class 0101: 1095:0649 (rev 02)
00:1c.0 Class 0600: 103c:122e (rev 32)
00:1d.0 Class 0680: 103c:122a (rev 23)
00:1e.0 Class 0680: 103c:1229 (rev 23)
20:01.0 Class 0100: 1000:0030 (rev 08)
20:01.1 Class 0100: 1000:0030 (rev 08)
20:02.0 Class 0200: 8086:1079 (rev 03)
20:02.1 Class 0200: 8086:1079 (rev 03)
20:1e.0 Class 0600: 103c:122e (rev 32)
40:1e.0 Class 0600: 103c:122e (rev 32)
80:1e.0 Class 0600: 103c:122e (rev 32)
e0:01.0 Class 0780: 103c:1290 (rev 01)
e0:01.1 Class 0700: 103c:1048 (rev 03)
e0:02.0 Class 0300: 1002:5159
e0:1e.0 Class 0600: 103c:122e (rev 32)
Cytat: alvaro
i ewentualnie USB:
lsusb
[root@localhost root]# lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 002 Device 002: ID 046d:c05a Logitech, Inc.
Bus 001 Device 001: ID 0000:0000
Bus 001 Device 003: ID 0e8f:0022
Cytat: alvaro
Dodatkowo możesz podać informacje na temat załadowanych modułów jądra:
lsmod
[root@localhost root]# lsmod
Module                  Size  Used by    Not tainted
ide-cd                 72016   0  (autoclean)
cdrom                  70244   0  (autoclean) [ide-cd]
button                  9400   0  (unused)
autofs                 30864   0  (autoclean) (unused)
ipt_REJECT             11768   1  (autoclean)
ipt_state               2824   1  (autoclean)
ip_conntrack           67176   1  (autoclean) [ipt_state]
iptable_filter          4680   1  (autoclean)
ip_tables              38440   3  [ipt_REJECT ipt_state iptable_filter]
nls_iso8859-1           5984   1  (autoclean)
nls_cp437               7680   1  (autoclean)
vfat                   30336   1  (autoclean)
fat                    85708   0  (autoclean) [vfat]
keybdev                 5976   0  (unused)
mousedev               14688   1
hid                    49544   0  (unused)
input                  13536   0  [keybdev mousedev hid]
ehci-hcd               51584   0  (unused)
usb-ohci               57856   0  (unused)
usbcore               180928   1  [hid ehci-hcd usb-ohci]
ext3                  214024   1
jbd                   127680   1  [ext3]
mptscsih               92168   3
mptbase                96992   3  [mptscsih]
sd_mod                 32352   6
scsi_mod              229248   2  [mptscsih sd_mod]
Cytat: alvaro
oraz jego wersję:
uname -r
[root@localhost root]# uname -r
2.4.21-4.EL
Cytat: alvaro
Pomocne może okazać się także:
dmesg
[root@localhost root]# dmesg
Linux version 2.4.21-4.EL (bhcompile@rocky.devel.redhat.com) (gcc version 3.2.3 20030502 (Red Hat Linux 3.2.3-20)) #1 SMP Fri Oct 3 17:29:39 EDT 2003
EFI v1.10 by HP: SALsystab=0x3ea7a000 ACPI 2.0=0x3ffec000 SMBIOS=0x3ea7c000 HCDP=0x3ffea000
CPU 0: mapping PAL code [0x3f400000-0x3f800000) into [0xe00000003f000000-0xe000000040000000)
efi.trim_bottom: ignoring 636KB of memory at 0x1000 due to granule hole at 0x0
efi.trim_bottom: ignoring 15360KB of memory at 0x100000 due to granule hole at 0x0
Initial ramdisk at: 0xe0000040fee58000 (1327104 bytes)
SAL v3.01: oem=HP, product=
SAL: entry: pal_proc=0x3f408010, sal_proc=0x3fd3d030
SAL: Platform features
SAL: AP wakeup using external interrupt vector 0xff
booting generic kernel on platform hpzx1
CPU 0: 61 virtual and 50 physical address bits
ACPI: RSDP (v002     HP                     ) @ 0x000000003ffec000
ACPI: XSDT (v001     HP   rx1620 00000.00000) @ 0x000000003ffec02c
ACPI: FADT (v003     HP   rx1620 00000.00000) @ 0x000000003fff6068
ACPI: SPCR (v001     HP   rx1620 00000.00000) @ 0x000000003fff61a0
ACPI: DBGP (v001     HP   rx1620 00000.00000) @ 0x000000003fff61f0
ACPI: MADT (v001     HP   rx1620 00000.00000) @ 0x000000003fff6410
ACPI: SPMI (v004     HP   rx1620 00000.00000) @ 0x000000003fff6228
ACPI: CPEP (v001     HP   rx1620 00000.00000) @ 0x000000003fff62e0
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff4568
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff4718
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff4bc8
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff5458
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff5ce8
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff5e98
ACPI: SSDT (v001     HP   rx1620 00000.00006) @ 0x000000003fff5f78
ACPI:  (v000                 61440.00000) @ 0x0000000000000000
ACPI: Local APIC address 0xc0000000fee00000
ACPI: LAPIC_ADDR_OVR (address[00000000fee00000])
ACPI: LSAPIC (acpi_id[0x00] lsapic_id[0x00] lsapic_eid[0x00] enabled)
CPU 0 (0x0000) enabled (BSP)
ACPI: LSAPIC (acpi_id[0x01] lsapic_id[0x01] lsapic_eid[0x00] enabled)
CPU 1 (0x0100) enabled
ACPI: IOSAPIC (id[0x0] global_irq_base[0x10] address[00000000fed20800])
IOSAPIC: version 2.0, address 0xfed20800, GSIs 0x10-0x1a
ACPI: IOSAPIC (id[0x1] global_irq_base[0x1b] address[00000000fed22800])
IOSAPIC: version 2.0, address 0xfed22800, GSIs 0x1b-0x25
ACPI: IOSAPIC (id[0x2] global_irq_base[0x26] address[00000000fed24800])
IOSAPIC: version 2.0, address 0xfed24800, GSIs 0x26-0x30
ACPI: IOSAPIC (id[0x4] global_irq_base[0x31] address[00000000fed28800])
IOSAPIC: version 2.0, address 0xfed28800, GSIs 0x31-0x3b
ACPI: IOSAPIC (id[0x7] global_irq_base[0x3c] address[00000000fed2e800])
IOSAPIC: version 2.0, address 0xfed2e800, GSIs 0x3c-0x46
GSI 0x24(low,level) -> CPU 0x0000 vector 48
2 CPUs available, 2 CPUs total
Mca related initialization done
On node 0 totalpages: 259865
zone(0): 262144 pages.
zone(1): 16777208 pages.
zone(2): 0 pages.
Virtual mem_map starts at 0xa0007fff8e400000
Kernel command line: BOOT_IMAGE=scsi0:EFI\\redhat\\vmlinuz-2.4.21-4.EL  root=LABEL=/ ro
FPSWA interface at 0x40ffd08010, revision 1.18
CPU 0: base freq=266.667MHz, ITC ratio=12/2, ITC freq=1600.003MHz
Console: colour VGA+ 80x25
Calibrating delay loop... 2392.40 BogoMIPS
Memory: 4097968k/4157840k available (4195k code, 43776k reserved, 3438k data, 368k init)
Dentry cache hash table entries: 262144 (order: 8, 4194304 bytes)
Inode cache hash table entries: 262144 (order: 8, 4194304 bytes)
Mount cache hash table entries: 1024 (order: 0, 16384 bytes)
Buffer cache hash table entries: 262144 (order: 7, 2097152 bytes)
Page-cache hash table entries: 262144 (order: 7, 2097152 bytes)
POSIX conformance testing by UNIFIX
Boot processor id 0x0/0x0
SMP: starting up secondaries.
CPU 1: mapping PAL code [0x3f400000-0x3f800000) into [0xe00000003f000000-0xe000000040000000)
CPU 1: 61 virtual and 50 physical address bits
CPU 1: synchronized ITC with CPU 0 (last diff 2 cycles, maxerr 516 cycles)
CPU 1: base freq=266.667MHz, ITC ratio=12/2, ITC freq=1600.003MHz
CPU 1: checking for saved MCA error records
Calibrating delay loop... 2392.40 BogoMIPS
CPU1: CPU has booted.
Before bogomips.
Total of 2 processors activated (4784.80 BogoMIPS).
Starting migration thread for cpu 0
Starting migration thread for cpu 1
ACPI: Subsystem revision 20030619
PCI: Using SAL to access configuration space
ACPI: Interpreter enabled
ACPI: Using IOSAPIC for interrupt routing
ACPI: System [ACPI] (supports S5)
ACPI: PCI Root Bridge [L000] (00:00)
ACPI: PCI Interrupt Routing Table [\\_SB_.SBA0.L000._PRT]
ACPI: PCI Root Bridge [L001] (00:20)
ACPI: PCI Interrupt Routing Table [\\_SB_.SBA0.L001._PRT]
ACPI: PCI Root Bridge [L002] (00:40)
ACPI: PCI Interrupt Routing Table [\\_SB_.SBA0.L002._PRT]
ACPI: PCI Root Bridge [L004] (00:80)
ACPI: PCI Interrupt Routing Table [\\_SB_.SBA0.L004._PRT]
ACPI: PCI Root Bridge [L007] (00:e0)
ACPI: PCI Interrupt Routing Table [\\_SB_.SBA0.L007._PRT]
CPU 0: checking for saved MCA error records
PCI->APIC IRQ transform: (00:01.0 INTA) -> CPU 0x0000 vector 49
PCI->APIC IRQ transform: (00:01.1 INTB) -> CPU 0x0100 vector 50
PCI->APIC IRQ transform: (00:01.2 INTC) -> CPU 0x0000 vector 51
PCI->APIC IRQ transform: (00:02.0 INTA) -> CPU 0x0100 vector 52
PCI->APIC IRQ transform: (20:01.0 INTA) -> CPU 0x0000 vector 53
PCI->APIC IRQ transform: (20:01.1 INTB) -> CPU 0x0100 vector 54
PCI->APIC IRQ transform: (20:02.0 INTA) -> CPU 0x0000 vector 55
PCI->APIC IRQ transform: (20:02.1 INTB) -> CPU 0x0100 vector 56
PCI->APIC IRQ transform: (e0:01.0 INTA) -> CPU 0x0000 vector 57
PCI->APIC IRQ transform: (e0:01.1 INTA) -> CPU 0x0100 vector 57
PCI->APIC IRQ transform: (e0:02.0 INTA) -> CPU 0x0000 vector 58
hpzx1: HWP0001 SBA at 0xfed00000; pci dev 00:1e.0
hpzx1: HWP0001 IOC at 0xfed01000; pci dev 00:1d.0
hpzx1: HWP0002 PCI LBA _BBN 0x00 at 0xfed20000; pci dev 00:1c.0
hpzx1: HWP0002 PCI LBA _BBN 0x20 at 0xfed22000; pci dev 20:1e.0
hpzx1: HWP0002 PCI LBA _BBN 0x40 at 0xfed24000; pci dev 40:1e.0
hpzx1: HWP0002 PCI LBA _BBN 0x80 at 0xfed28000; pci dev 80:1e.0
hpzx1: HWP0002 PCI LBA _BBN 0xe0 at 0xfed2e000; pci dev e0:1e.0
IOC: zx1 2.3 HPA 0xfed01000 IOVA space 1024Mb at 0x40000000
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
perfmon: version 1.3 IRQ 238
perfmon: 16 PMCs, 18 PMDs, 4 counters (47 bits)
PAL Information Facility v0.5
EFI Variables Facility v0.05 2002-Mar-26
+BEGIN HARDWARE ERROR STATE AT CPE
+Err Record ID: 43    SAL Rev:  0.02
+Time: 01/06/2014 14:54:16    Severity 2
+Platform Memory Device Error Info Section
+ Mem Error Detail:  Error Status: 0x441000, Physical Address: 0x3ffe3180, Card: 66, Module: 48, ,Responder Address: 0xfed00000, Bus Specific Data: 0x20,
 OEM Memory Controller ID: 2b 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 OEM Specific Data: 28 01 00 00 00 00 00 00 aa ac 73 14 93 dc 8d 47 97 42 aa 85 4f 51 0c fb ff 1d 00 00 00 00 00 00 17 01 00 00 00 00 00 00 80 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 32 fe 3f 80 18 00 ff 00 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40 32 fe 3f 07 f0 fd 3f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00 40 00 00 00 00 00 00 00 40 00 00 00 00 00 00 80 31 fe 3f 00 00 44 08 00 00 00 00 00 00 00 00 00 08 00 00 00 00 00 00 00 32 fe 3f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+Platform Memory Device Error Info Section
+ Mem Error Detail:  Error Status: 0x41000, Physical Address: 0x3ffe3200, Card: 66, Module: 48, ,Responder Address: 0xfed00000, Bus Specific Data: 0x20,
 OEM Memory Controller ID: 2b 12 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+END HARDWARE ERROR STATE AT CPE
Total HugeTLB memory allocated, 0
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 64966
aio_setup: sizeof(struct page) = 112
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ DETECT_IRQ SERIAL_PCI SERIAL_ACPI enabled
ttyS0 at 0xc0000000f4050000 (irq = 57) is a 16550A
GSI 0x22(low,level) -> CPU 0x0000 vector 59
ttyS1 at iomem 0xc0000000ff5e0000 (irq = 59) is a 16550A
PCI: Found IRQ 57 for device e0:01.0
ttyS2 at iomem 0xc0000000f4051000 (irq = 57) is a 16550A
PCI: Found IRQ 57 for device e0:01.1
ttyS0 at iomem 0xc0000000f4050000 (irq = 57) is a 16550A
ttyS3 at iomem 0xc0000000f4050010 (irq = 57) is a 16550A
ttyS4 at iomem 0xc0000000f4050038 (irq = 57) is a 16550A
EFI Time Services Driver v0.4
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CMD649: IDE controller at PCI slot 00:02.0
PCI: Found IRQ 52 for device 00:02.0
CMD649: chipset revision 2
CMD649: 100% native mode on irq 52
    ide0: BM-DMA at 0x0d00-0x0d07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x0d08-0x0d0f, BIOS settings: hdc:pio, hdd:pio
hda: DV-28E-N, ATAPI CD/DVD-ROM drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
global_restore_flags: 10084a6010 (e0000000049809f0)
ide0 at 0xd18-0xd1f,0xd26 on irq 52
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 65536 buckets, 1024Kbytes
TCP: Hash tables configured (established 2097152 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1296kB freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
Fusion MPT base driver 2.05.05+
Copyright (c) 1999-2002 LSI Logic Corporation
PCI: Found IRQ 53 for device 20:01.0
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator,Target}
PCI: Found IRQ 54 for device 20:01.1
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator,Target}
mptbase: 2 MPT adapters found, 2 installed.
Fusion MPT SCSI Host driver 2.05.05+
scsi0 : ioc0: LSI53C1030, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=53
scsi1 : ioc1: LSI53C1030, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=54
Starting timer : 0 0
blk: queue e000004045bf6d30, I/O limit 17592186044415Mb (mask 0xffffffffffffffff)
  Vendor: FUJITSU   Model: MAP3735NC         Rev: 5207
  Type:   Direct-Access                      ANSI SCSI revision: 03
Starting timer : 0 0
blk: queue e000004045bf6930, I/O limit 17592186044415Mb (mask 0xffffffffffffffff)
mptscsih: ioc0: scsi0: Id=1 Lun=0: Queue depth=31
Starting timer : 0 0
Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
SCSI device sda: 143571316 512-byte hdwr sectors (73509 MB)
Partition check:
 sda: sda1 sda2 sda3
Journalled Block Device driver loaded
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 368kB freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Found IRQ 49 for device 00:01.0
usb-ohci.c: USB OHCI at membase 0xc000000080002000, IRQ 49
usb-ohci.c: usb-00:01.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Found IRQ 50 for device 00:01.1
usb-ohci.c: USB OHCI at membase 0xc000000080001000, IRQ 50
usb-ohci.c: usb-00:01.1, NEC Corporation USB (#2)
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: new USB device 00:01.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0xe8f/0x22) is not claimed by any active driver.
PCI: Found IRQ 51 for device 00:01.2
ehci-hcd 00:01.2: NEC Corporation USB 2.0
ehci-hcd 00:01.2: irq 51, pci mem c000000080000000
usb.c: new USB bus registered, assigned bus number 3
ehci-hcd 00:01.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 5 ports detected
usb.c: error getting string descriptor 0 (error=-110)
usb.c: error getting string descriptor 0 (error=-110)
usb.c: error getting string descriptor 0 (error=-110)
usb.c: error getting string descriptor 0 (error=-110)
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
Adding Swap: 2040208k swap-space (priority -1)
hub.c: connect-debounce failed, port 1 disabled
hub.c: new USB device 00:01.1-1, assigned address 2
input0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb2:2.0
usb.c: USB disconnect on device 00:01.0-1 address 2
hub.c: new USB device 00:01.0-1, assigned address 3
input1: USB HID v1.10 Keyboard [GASIA USB KB V11] on usb1:3.0
input2: USB HID v1.10 Pointer [GASIA USB KB V11] on usb1:3.1
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8192 buckets, 65536 max) - 448 bytes per conntrack
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
ide-floppy driver 0.99.newide
hda: attached ide-cdrom driver.
hda: ATAPI 24X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
cdrom: This disc doesn't have any tracks I recognize!
keyboard.c: can't emulate rawmode for keycode 272
keyboard.c: can't emulate rawmode for keycode 272
keyboard.c: can't emulate rawmode for keycode 272
keyboard.c: can't emulate rawmode for keycode 272
keyboard.c: can't emulate rawmode for keycode 273
keyboard.c: can't emulate rawmode for keycode 273
keyboard.c: can't emulate rawmode for keycode 272
keyboard.c: can't emulate rawmode for keycode 272
Cytat: alvaro
Na koniec drobna uwaga - rozszerzone wsparcie (Extended Life Cycle) dla RHEL 3 kończy się w tym miesiącu. Wypadałoby już przygotować się do migracji na nowszą wersję lub inny system.
Jak na razie to raczej w testach szkoleniowych więc nie śpieszno mi do migracji aż tak bardzo.

alvaro

  • Gość
Brak połączenia z siecią RHEL3 i HP integrity RX1620
« Odpowiedź #3 dnia: 2014-01-06, 17:44:31 »
[root@localhost root]# ifconfig
lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:212 errors:0 dropped:0 overruns:0 frame:0
          TX packets:212 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:16286 (15.9 Kb)  TX bytes:16286 (15.9 Kb)
System nie widzi w ogóle żadnego interfejsu sieciowego oprócz oczywiście Loopback.

20:02.0 Class 0200: 8086:1079 (rev 03)
Z powyższego wynika, że komputer wyposażony jest w kartę sieciową 82546GB Gigabit Ethernet Controller.
Sterowniki do niego można pobrać ze strony Intela.
Najnowszy wersja to 8.0.35.
Źródła są także dostępne na stronie stronie projektu e1000 (Intel Ethernet Drivers and Utilities) na sf.net.

Instalacja powinna przebiegać mniej więcej tak:
tar zxvf e1000-8.0.35.tar.gz
cd e1000-8.0.35/src/
make
su -c "make install"
Po instalacji może zajść konieczność załadowania modułu jądra:
modprobe e1000
Jeśli wszystko się powiedzieć to ifconfig powinien pokazywać nowy interfejs sieciowy (prawdopodobnie eth0).

miniol87

  • Gość
Brak połączenia z siecią RHEL3 i HP integrity RX1620
« Odpowiedź #4 dnia: 2014-01-06, 18:22:51 »
alvaro
Jesteś wielki!

Jak będziesz w okolicy to upomnij się o duże zimne piwo :)
Swoją drogą też dzięki za instrukcję "krok po kroku", bo bez tego pewnie bym o wiele więcej czasu zmarnował.
Temat do zamknięcia.