Sprzęt > Napędy CD/DVD
Problemy z dyskiem
taczmi:
Witam serdecznie. Mam Suse 11.4 i ostatnio podczas uruchamiania komputera
pojawiła mi się informacja:
SMART Failre Predicted on herd disk 0:....
WANING: imediately back-up your data and replace your hard disk drive. A
failure may by imminent
F1 to Continue
Wnioskuje z tego ze mam uszkodzony dysk. Czy mogę go jakoś naprawić nie
tracą informacji? Czy mogę się posłużyć oprogramowaniem Hiren'sBootCD?
Jeśli tak to który jest najlepszy do naprawy błędu.
Po informacji jaka udało mi się uzyskać to mam w jednym sektorze ERROR i
wychodzi mi błąd w realokacji.
Dziwne bo laptop mi nigdzie nie spadł a co za tym idzie dysk. Wnioskuje ze
to jakiś błąd fizyczny.
Bardzo proszę o pomoc w usunięciu tego problemu.
rilicek:
Rozumiem, że komunikat pokazuje się przed startem systemu i jest to komunikat biosu.
Oznacza on, że parametry SMART wskazują na możliwość awarii dysku w najbliższym czasie.
Naprawić dysku raczej się nie da. Póki co powinieneś mieć dostęp do wszystkich swoich danych, dopóki dysk naprawdę nie padnie.
Masz dwa wyjścia:
1. Jesteś "Hardkorem" i jedziesz dalej na tym dysku i testujesz kiedy rzeczywiście padnie.
2. Jesteś mięczakiem, kupujesz nowy dysk i kopiujesz wszystko ze starego na nowy. Ze starego robisz podstawkę pod kwiaty lub co sobie tylko wymyślisz.
taczmi:
Stały bywalec napisał:Masz dwa wyjścia:
"1. Jesteś "Hardkorem" i jedziesz dalej na tym dysku i testujesz kiedy rzeczywiście padnie.
2. Jesteś mięczakiem, kupujesz nowy dysk i kopiujesz wszystko ze starego na nowy. Ze starego robisz podstawkę pod kwiaty lub co sobie tylko wymyślisz."
"Czy jest możliwość wykasowania tej informacji aby ona się nie pojawiała?
W biosie nie mam możliwości wyłączenia smart, ale posiadam płytkę
HirensBootCD, pytanie tylko jaki program użyć do usunięcia tej pojawiającej
się informacji."
rilicek:
Podaj
--- Kod: ---
smartctl -a /dev/sda
--- Koniec kodu ---
gdzie /dev/sda - to twój uszkodzony dysk.
1. Parametrów S.M.A.R.T. raczej nie da się wykasować, więc komunikat będzie się pojawiał.
2. Współczesne dyski z założenia przenoszą same dane z uszkodzonych sektorów do dobrych bez wiedzy użyszkodnika. Zaczynają się drzeć jak im zapasowych zaczyna braknąć.
Mogę się mylić, więc chętnie poczytam jak naprawić taki błąd.
taczmi:
Po wpisaniu kodu wylistowało informacje, ale czy możesz mi to rozszyfrować
jak temu problemowi zaradzić..?
smartctl 5.40 2010-10-16 r3189 [i686-pc-linux-gnu] (SUSE RPM)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA family
Device Model: WDC WD3200BEVT-22ZCT0
Serial Number: WD-WXE708LD9794
Firmware Version: 11.01A11
User Capacity: 320,072,933,376 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Dec 7 16:26:33 2012 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: (10800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported..
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0027 186 184 021 Pre-fail Always
- 1666
4 Start_Stop_Count 0x0032 093 093 000 Old_age Always
- 7187
5 Reallocated_Sector_Ct 0x0033 137 137 140 Pre-fail Always
FAILING_NOW 500
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always
- 0
9 Power_On_Hours 0x0032 073 073 000 Old_age Always
- 20369
10 Spin_Retry_Count 0x0033 100 099 051 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 093 093 000 Old_age Always
- 7064
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always
- 521
193 Load_Cycle_Count 0x0032 038 038 000 Old_age Always
- 487264
194 Temperature_Celsius 0x0022 101 074 000 Old_age Always
- 46
196 Reallocated_Event_Count 0x0032 175 175 000 Old_age Always
- 25
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always
- 2
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline
- 2
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline
- 0
SMART Error Log Version: 1
ATA Error Count: 982 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 982 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 4b 1e bf e0 Error: UNC at LBA = 0x00bf1e4b = 12525131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 4b 1e bf 24 00 02:05:26.718 READ VERIFY SECTOR(S) EXT
42 ff 01 4a 1e bf 24 00 02:05:26.717 READ VERIFY SECTOR(S) EXT
42 ff 01 49 1e bf 24 00 02:05:26.716 READ VERIFY SECTOR(S) EXT
42 ff 01 48 1e bf 24 00 02:05:26.715 READ VERIFY SECTOR(S) EXT
42 ff 01 47 1e bf 24 00 02:05:26.714 READ VERIFY SECTOR(S) EXT
Error 981 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 7f 1f 1e bf e0 Error: UNC at LBA = 0x00bf1e1f = 12525087
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 7f 1f 1e bf 24 00 02:05:23.194 READ VERIFY SECTOR(S) EXT
42 ff 7f a0 1d bf 24 00 02:05:23.192 READ VERIFY SECTOR(S) EXT
42 ff 7f 21 1d bf 24 00 02:05:23.190 READ VERIFY SECTOR(S) EXT
42 ff 7f a2 1c bf 24 00 02:05:23.189 READ VERIFY SECTOR(S) EXT
42 ff 7f 23 1c bf 24 00 02:05:23.187 READ VERIFY SECTOR(S) EXT
Error 980 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 4c 61 b3 e0 Error: UNC at LBA = 0x00b3614c = 11755852
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 4c 61 b3 24 00 02:05:07.965 READ VERIFY SECTOR(S) EXT
42 ff 01 4b 61 b3 24 00 02:05:07.964 READ VERIFY SECTOR(S) EXT
42 ff 01 4a 61 b3 24 00 02:05:07.963 READ VERIFY SECTOR(S) EXT
42 ff 01 49 61 b3 24 00 02:05:07.962 READ VERIFY SECTOR(S) EXT
42 ff 01 48 61 b3 24 00 02:05:07.961 READ VERIFY SECTOR(S) EXT
Error 979 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 7f 48 61 b3 e0 Error: UNC at LBA = 0x00b36148 = 11755848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 7f 48 61 b3 24 00 02:05:04.491 READ VERIFY SECTOR(S) EXT
42 ff 7f c9 60 b3 24 00 02:05:04.489 READ VERIFY SECTOR(S) EXT
42 ff 7f 4a 60 b3 24 00 02:05:04.487 READ VERIFY SECTOR(S) EXT
42 ff 7f cb 5f b3 24 00 02:05:04.486 READ VERIFY SECTOR(S) EXT
42 ff 7f 4c 5f b3 24 00 02:05:04.485 READ VERIFY SECTOR(S) EXT
Error 978 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 49 5e b3 e0 Error: UNC at LBA = 0x00b35e49 = 11755081
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 49 5e b3 24 00 02:05:01.230 READ VERIFY SECTOR(S) EXT
42 ff 01 48 5e b3 24 00 02:05:01.229 READ VERIFY SECTOR(S) EXT
42 ff 01 47 5e b3 24 00 02:05:01.228 READ VERIFY SECTOR(S) EXT
42 ff 01 46 5e b3 24 00 02:05:01.227 READ VERIFY SECTOR(S) EXT
42 ff 01 45 5e b3 24 00 02:05:01.226 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed: unknown failure 90% 20340
-
# 2 Conveyance offline Completed: unknown failure 90% 20340
-
# 3 Extended offline Completed: unknown failure 90% 20340
-
# 4 Short offline Completed without error 00% 2916
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Nawigacja
[#] Następna strona
Idź do wersji pełnej