Po wpisaniu kodu wylistowało informacje, ale czy możesz mi to rozszyfrować
jak temu problemowi zaradzić..?
smartctl 5.40 2010-10-16 r3189 [i686-pc-linux-gnu] (SUSE RPM)
Copyright (C) 2002-10 by Bruce Allen,
http://smartmontools.sourceforge.net=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Blue Serial ATA family
Device Model: WDC WD3200BEVT-22ZCT0
Serial Number: WD-WXE708LD9794
Firmware Version: 11.01A11
User Capacity: 320,072,933,376 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Dec 7 16:26:33 2012 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has
ever
been run.
Total time to complete Offline
data collection: (10800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported..
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 127) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0027 186 184 021 Pre-fail Always
- 1666
4 Start_Stop_Count 0x0032 093 093 000 Old_age Always
- 7187
5 Reallocated_Sector_Ct 0x0033 137 137 140 Pre-fail Always
FAILING_NOW 500
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always
- 0
9 Power_On_Hours 0x0032 073 073 000 Old_age Always
- 20369
10 Spin_Retry_Count 0x0033 100 099 051 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 093 093 000 Old_age Always
- 7064
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always
- 521
193 Load_Cycle_Count 0x0032 038 038 000 Old_age Always
- 487264
194 Temperature_Celsius 0x0022 101 074 000 Old_age Always
- 46
196 Reallocated_Event_Count 0x0032 175 175 000 Old_age Always
- 25
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always
- 2
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline
- 2
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline
- 0
SMART Error Log Version: 1
ATA Error Count: 982 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 982 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 4b 1e bf e0 Error: UNC at LBA = 0x00bf1e4b = 12525131
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 4b 1e bf 24 00 02:05:26.718 READ VERIFY SECTOR(S) EXT
42 ff 01 4a 1e bf 24 00 02:05:26.717 READ VERIFY SECTOR(S) EXT
42 ff 01 49 1e bf 24 00 02:05:26.716 READ VERIFY SECTOR(S) EXT
42 ff 01 48 1e bf 24 00 02:05:26.715 READ VERIFY SECTOR(S) EXT
42 ff 01 47 1e bf 24 00 02:05:26.714 READ VERIFY SECTOR(S) EXT
Error 981 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 7f 1f 1e bf e0 Error: UNC at LBA = 0x00bf1e1f = 12525087
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 7f 1f 1e bf 24 00 02:05:23.194 READ VERIFY SECTOR(S) EXT
42 ff 7f a0 1d bf 24 00 02:05:23.192 READ VERIFY SECTOR(S) EXT
42 ff 7f 21 1d bf 24 00 02:05:23.190 READ VERIFY SECTOR(S) EXT
42 ff 7f a2 1c bf 24 00 02:05:23.189 READ VERIFY SECTOR(S) EXT
42 ff 7f 23 1c bf 24 00 02:05:23.187 READ VERIFY SECTOR(S) EXT
Error 980 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 4c 61 b3 e0 Error: UNC at LBA = 0x00b3614c = 11755852
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 4c 61 b3 24 00 02:05:07.965 READ VERIFY SECTOR(S) EXT
42 ff 01 4b 61 b3 24 00 02:05:07.964 READ VERIFY SECTOR(S) EXT
42 ff 01 4a 61 b3 24 00 02:05:07.963 READ VERIFY SECTOR(S) EXT
42 ff 01 49 61 b3 24 00 02:05:07.962 READ VERIFY SECTOR(S) EXT
42 ff 01 48 61 b3 24 00 02:05:07.961 READ VERIFY SECTOR(S) EXT
Error 979 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 7f 48 61 b3 e0 Error: UNC at LBA = 0x00b36148 = 11755848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 7f 48 61 b3 24 00 02:05:04.491 READ VERIFY SECTOR(S) EXT
42 ff 7f c9 60 b3 24 00 02:05:04.489 READ VERIFY SECTOR(S) EXT
42 ff 7f 4a 60 b3 24 00 02:05:04.487 READ VERIFY SECTOR(S) EXT
42 ff 7f cb 5f b3 24 00 02:05:04.486 READ VERIFY SECTOR(S) EXT
42 ff 7f 4c 5f b3 24 00 02:05:04.485 READ VERIFY SECTOR(S) EXT
Error 978 occurred at disk power-on lifetime: 20342 hours (847 days + 14
hours)
When the command that caused the error occurred, the device was active
or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 49 5e b3 e0 Error: UNC at LBA = 0x00b35e49 = 11755081
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
42 ff 01 49 5e b3 24 00 02:05:01.230 READ VERIFY SECTOR(S) EXT
42 ff 01 48 5e b3 24 00 02:05:01.229 READ VERIFY SECTOR(S) EXT
42 ff 01 47 5e b3 24 00 02:05:01.228 READ VERIFY SECTOR(S) EXT
42 ff 01 46 5e b3 24 00 02:05:01.227 READ VERIFY SECTOR(S) EXT
42 ff 01 45 5e b3 24 00 02:05:01.226 READ VERIFY SECTOR(S) EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed: unknown failure 90% 20340
-
# 2 Conveyance offline Completed: unknown failure 90% 20340
-
# 3 Extended offline Completed: unknown failure 90% 20340
-
# 4 Short offline Completed without error 00% 2916
-
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.