Problem z instalacją sterownika LogiLink Wireless N 150Mbps USB Adapte

[Bubek789]

Witam Linuxa używam od niedawna i mam problem z czynnościami na pozór łatwymi. Nie wiem jak zainsatlować sterowników LogiLink Wireless N 150Mbps USB Adapter, próbowałem wpisywać jakieś kody, ale nic nie wychodziło. Oto jakaś instrukcja.
Software Package - Component
===============================================================================
   1. ReleaseNotes.doc

   2. document/

   3. driver source code

      3.1 Makefile - to build the modules

      3.2 Script and configuration for DHCP:
         "wlan0dhcp"
         "ifcfg-wlan0"

      3.3 Example of supplicant configuration file:
         "wpa1.conf"

      3.4 Script to run wpa_supplicant
         "runwpa"

      3.5 Script to clean relative modules
         "clean"

   4. wpa_supplicant/wpa_supplicant-0.6.9_wps_patch_20100201.zip
         The tool help the wlan network to communicate under the
         protection of WPAPSK mechanism (WPA/WPA2) and add WPS patch


==================================================================================================================
      User Guide(1) - connecting wireless networking using "Network Manager" GUI utility (For PC Linux)
==================================================================================================================
         (1) Network Manager is a utility attempts to make use of wireless networking easy.

         (2) Notes: if you want to use the following command-line method to connect wireless networking,
                  please disable the "Network Manager", because "Network Manager" will conflict with method of command line .

==================================================================================================================
      User Guide(2) - Using the wpa_cli & wpa_supplicant tools (For embedded Linux)
==================================================================================================================

   Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

==================================================================================================================
      User Guide(3) - Set wireless lan MIBs in Command Line (Legacy command - Not recommend)
==================================================================================================================
This driver uses Wireless Extension as an interface allowing you to set
Wireless LAN specific parameters.

Current driver supports "iwlist" to show the device status of nic
        iwlist wlan0 [parameters]
where
        parameter explaination         [parameters]
        -----------------------        -------------
        Show available chan and freq   freq / channel
        Show and Scan BSS and IBSS    scan[ning]
        Show supported bit-rate         rate / bit[rate]

For example:
   iwlist wlan0 channel
   iwlist wlan0 scan
   iwlist wlan0 rate

Driver also supports "iwconfig", manipulate driver private ioctls, to set
MIBs.

   iwconfig wlan0 [parameters] [val]
where
   parameter explaination      [parameters]        [val] constraints
        -----------------------     -------------        ------------------
        Connect to AP by address    ap                 [mac_addr]
        Set the essid, join (I)BSS  essid                [essid]
        Set operation mode          mode                {Managed|Ad-hoc}
        Set keys and security mode  key/enc[ryption]    {N|open|restricted|off}

For example:
   iwconfig wlan0 essid "ap_name"
   iwconfig wlan0 ap XX:XX:XX:XX:XX:XX
   iwconfig wlan0 mode Ad-hoc
   iwconfig wlan0 essid "name" mode Ad-hoc
   iwconfig wlan0 key 0123456789 [2] open
   iwconfig wlan0 key off
   iwconfig wlan0 key restricted [3] 0123456789
        Note: Better to set these MIBS without GUI such as NetworkManager and be sure that our
              nic has been brought up before these settings. WEP key index 2-4 is not supportted by
              NetworkManager.

===============================================================================
      Getting IP address (For User Guide(2) & User Guide(3))
===============================================================================
After start up the nic and connect to AP successfully, the network needs to obtain an IP address
before transmit/receive data.
This can be done by setting the static IP via "ifconfig wlan0 IP_ADDRESS"
command, or using DHCP.

If using DHCP, setting steps is as below:
   (1)check if the WiFi had connected to an AP via "iwconfig" command
      $> iwconfig

   (2)run the script which run the dhclient
      $> ./wlan0dhcp
           or
      dhcpcd wlan0
                 (Some network admins require that you use the
                 hostname and domainname provided by the DHCP server.
                 In that case, use
      dhcpcd -HD wlan0)


===============================================================================
      WPAPSK/WPA2PSK - using wpa_supplicant (For User Guide(3))
===============================================================================

   Wpa_supplicant helps to secure wireless connection with the protection of
WPAPSK/WPA2PSK mechanism. Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

===============================================================================
      WPS - PIN & PBC methods
===============================================================================

      (*) Please refer to the document/wpa_cli_with_wpa_supplicant_20091227.doc

===============================================================================
      Power Saving Mode
===============================================================================

      (1) in order to enter PS Mode, you need to add the parameter of "power_mgnt=1" when executing "insmod 8192cu.ko" :
             $>insmod 8192cu.ko power_mgnt=1
             or
             $>insmod 8192cu.ko power_mgnt=2

      (2) Notes:
            power_mgnt=0 /default, disable PS
            power_mgnt=1 /enable PS, MIN_PS Mode
            power_mgnt=2 /enable PS, MAX_PS Mode
Ma ktoś jakieś pomysły?

[Ksanderon]

wykonaj cały punkt 3 i user guide(1)

[Bubek789]

W tym 3 punkcie to "wlan0dhcp" "ifcfg-wlan0" trzeba z kopiować do terminalu, bo wyskakuje not found