Autor Wątek: [DEBIAN] Instalacja karty wifi (Przeczytany 9092 razy)

schabowy · « **dnia:** 2011-10-12, 22:31:18 »

Prosze o pomoc w instalacji karty wifi. Linuksa mam od wczoraj i nie mam pojęcia jak się za to zabrać. Szukając w internecie sposobu na konfiguracje karty wifi naktnąłem się na takie polecenia jak ifconfig i iwconfig. Być może w konfiguracji pomogą wyniki:

Cytuj

root@debian:/home/user1# ifconfig -a
eth0 Link encap:Ethernet HWaddr 70:5a:b6:88:58:ad
inet addr:192.168.1.90 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::725a:b6ff:fe88:58ad/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:36128 errors:0 dropped:0 overruns:0 frame:0
TX packets:36019 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:33307134 (31.7 MiB) TX bytes:5230116 (4.9 MiB)
Interrupt:31 Base address:0xe000

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 B) TX bytes:560 (560.0 B)

pan0 Link encap:Ethernet HWaddr ba:f8:6c:65:54:5f
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

Cytuj

root@debian:/home/user1# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

pan0 no wireless extensions.

Drugą sprawą jest ikonka sieci na panelu - sygnalizuje że nie jestem w ogóle połączony z internetem, a w rzeczywistości jestem połączony przez ethernet. Mam też wątpliwości co do tego połączenia, udaje się połączyć jedynie wtedy kiedy kabel ethernetowy jest podpiety podczas uruchamiania systemu. Jeśli zostanie podpiety kiedy system jest juz uruchomiony nie mogę uzyskać połączenia.

ultr · « **Odpowiedź #1 dnia:** 2011-10-13, 02:53:54 »

Wykonaj polecenia
lspci -vv > lspci.txt
dmesg > dmesg.txt
I wklej zawartość obu plików tutaj (w tagu CODE), albo na jakąś wrzutę czy inny serwis trzymający wklejoną treść.

Zapewne nie masz zainstalowanego firmwaru dla karty wifi.
Ale to trzeba najpierw określić jej producenta i model (powyższe polecenie lspci, dmesg też może pokazać błąd ładowania firmware).

Co do ikonki, odpal synaptica i zainstaluj network-manager albo wicd. I zrestartuj komputer.

schabowy · « **Odpowiedź #2 dnia:** 2011-10-13, 13:07:03 »

lspci -vv:

Kod: [Zaznacz]

user1@debian:~$ lspci -vv
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Capabilities: 

00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: d2000000-d30fffff
	Prefetchable memory behind bridge: 00000000c0000000-00000000d1ffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d9405000 (64-bit, non-prefetchable) [size=16]
	Capabilities: 

00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) (prog-if 20 [EHCI])
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d9408000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: 
	Kernel driver in use: ehci_hcd

00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 22
	Region 0: Memory at d9400000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: 
	Kernel driver in use: HDA Intel

00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=02, subordinate=06, sec-latency=0
	I/O behind bridge: 00009000-00009fff
	Memory behind bridge: d8c00000-d93fffff
	Prefetchable memory behind bridge: 00000000d3100000-00000000d38fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=07, subordinate=0b, sec-latency=0
	I/O behind bridge: 00007000-00008fff
	Memory behind bridge: d8300000-d8bfffff
	Prefetchable memory behind bridge: 00000000d3900000-00000000d40fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=0c, subordinate=10, sec-latency=0
	I/O behind bridge: 00005000-00006fff
	Memory behind bridge: d7b00000-d82fffff
	Prefetchable memory behind bridge: 00000000d4100000-00000000d49fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=11, subordinate=15, sec-latency=0
	I/O behind bridge: 00004000-00004fff
	Memory behind bridge: d7300000-d7afffff
	Prefetchable memory behind bridge: 00000000d4a00000-00000000d51fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=16, subordinate=1a, sec-latency=0
	I/O behind bridge: 00003000-00003fff
	Memory behind bridge: d6a00000-d72fffff
	Prefetchable memory behind bridge: 00000000d5200000-00000000d59fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 05) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=1b, subordinate=1f, sec-latency=0
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: d6200000-d69fffff
	Prefetchable memory behind bridge: 00000000d5a00000-00000000d61fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 
	Kernel driver in use: pcieport

00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05) (prog-if 20 [EHCI])
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 23
	Region 0: Memory at d9407000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: 
	Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Bus: primary=00, secondary=20, subordinate=20, sec-latency=32
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: 

00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
	Capabilities: 

00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 05) (prog-if 01 [AHCI 1.0])
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Latency: 0
	Interrupt: pin B routed to IRQ 32
	Region 0: I/O ports at b048 [size=8]
	Region 1: I/O ports at b054 [size=4]
	Region 2: I/O ports at b040 [size=8]
	Region 3: I/O ports at b050 [size=4]
	Region 4: I/O ports at b020 [size=32]
	Region 5: Memory at d9408800 (32-bit, non-prefetchable) [size=2K]
	Capabilities: 
	Kernel driver in use: ahci

00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR- 	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at d9404000 (64-bit, non-prefetchable) [size=256]
	Region 4: I/O ports at efa0 [size=32]

01:00.0 VGA compatible controller: nVidia Corporation GT218 [GeForce 310M] (rev a2) (prog-if 00 [VGA controller])
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d2000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
	Region 3: Memory at d0000000 (64-bit, prefetchable) [size=32M]
	Region 5: I/O ports at a000 [size=128]
	Expansion ROM at d3080000 [disabled] [size=512K]
	Capabilities: 
	Kernel driver in use: nouveau

01:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: 
	Kernel driver in use: HDA Intel

07:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10)
	Subsystem: Realtek Semiconductor Co., Ltd. Device 8181
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at 7000 [size=256]
	Region 1: Memory at d8300000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: 

0c:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
	Subsystem: Toshiba America Info Systems Device ff00
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0, Cache Line Size: 32 bytes
	Interrupt: pin A routed to IRQ 31
	Region 0: I/O ports at 5000 [size=256]
	Region 2: Memory at d4104000 (64-bit, prefetchable) [size=4K]
	Region 4: Memory at d4100000 (64-bit, prefetchable) [size=16K]
	Expansion ROM at d4120000 [disabled] [size=128K]
	Capabilities: 
	Kernel driver in use: r8169

16:00.0 System peripheral: JMicron Technology Corp. SD/MMC Host Controller (rev 20)
	Subsystem: Toshiba America Info Systems Device ff08
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d6a00300 (32-bit, non-prefetchable) [size=256]
	Capabilities: 
	Kernel driver in use: sdhci-pci

16:00.2 SD Host controller: JMicron Technology Corp. Standard SD Host Controller (rev 20) (prog-if 01)
	Subsystem: Toshiba America Info Systems Device ff08
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d6a00200 (32-bit, non-prefetchable) [size=256]
	Capabilities: 

16:00.3 System peripheral: JMicron Technology Corp. MS Host Controller (rev 20)
	Subsystem: Toshiba America Info Systems Device ff08
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at d6a00100 (32-bit, non-prefetchable) [size=256]
	Capabilities: 
	Kernel driver in use: jmb38x_ms

16:00.4 System peripheral: JMicron Technology Corp. xD Host Controller (rev 20)
	Subsystem: Toshiba America Info Systems Device ff08
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d6a00000 (32-bit, non-prefetchable) [size=256]
	Capabilities: 

ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
	Subsystem: Intel Corporation Device 8086
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0

ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
	Subsystem: Intel Corporation Device 8086
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0

ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
	Subsystem: Intel Corporation Device 8086
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0

ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
	Subsystem: Intel Corporation Device 8086
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0

ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
	Subsystem: Intel Corporation Device 8086
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0

ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
	Subsystem: Intel Corporation Device 8086
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR- 	Latency: 0

Andrzej J · « **Odpowiedź #3 dnia:** 2011-10-13, 17:24:22 »

Tu masz rozwiązanie
http://forums.debian.net/viewtopic.php?f=7&t=54167
Pozdrawiam
P.S. Jeżeli masz kernel 2.6.32-5 to możesz zainstalować firmware z backportów- druga metoda. Tu masz dodatkowe repozytoria dla squeeze http://dug.net.pl/tekst/136/lista_repozytoriow_%28sources_list%29_dla_debiana/#stable

ultr · « **Odpowiedź #4 dnia:** 2011-10-13, 21:20:42 »

Czyli, tak jak pisze Andrew_66, potrzebujesz pakietu firmware-realtek dla RTL8191SE:
http://packages.debian.org/search?keywords=firmware-realtek

Jeśli masz Debiana Wheezy (testing), to edytuj plik /etc/apt/sources.list i zmień linię z:

Kod: [Zaznacz]

deb http://ftp.pl.debian.org/debian/ wheezy main
deb-src http://ftp.pl.debian.org/debian/ wheezy main

na

Kod: [Zaznacz]

deb http://ftp.pl.debian.org/debian/ wheezy main contrib non-free
deb-src http://ftp.pl.debian.org/debian/ wheezy main contrib non-free

Potem:

Kod: [Zaznacz]

# apt-get update
# apt-get install firmware-realtek

I reboot.

Jeśli masz Debiana Squeeze (stable), to najprościej będzie ręcznie ściągnąć ten pakiet:
http://packages.debian.org/squeeze-backports/all/firmware-realtek/download
i zainstalować

Kod: [Zaznacz]

# dpkg -i firmware-realtek_0.32~bpo60+1_all.deb

I reboot.

Aktualności:

Linux.pl »

Nowe posty

Autor Wątek: [DEBIAN] Instalacja karty wifi (Przeczytany 9092 razy)

schabowy

[DEBIAN] Instalacja karty wifi

ultr

[DEBIAN] Instalacja karty wifi

schabowy

[DEBIAN] Instalacja karty wifi

Andrzej J

[DEBIAN] Instalacja karty wifi

ultr

[DEBIAN] Instalacja karty wifi