UStawienie sterowników dysku SATA w jadrze systemu

[migul]

Witam. Mam taki problem. Zainstalowalem sobie linuxa na swoim laptopie i problem polega na tym ze system chyba mi nie obsluguje kontrolera dysku SATA. Z tego co widze po pracy systemu kazde uruchomienie jakiejkolwiek aplikacji dlugo trwa i strasznie procesy jada po procesorze do tego stopnia ze dwa rdzenie wykorzystuje prawie po 100%. Jak skompilować jadro zeby ustawic zgodne sterowniki do obslugi dysku, tak zeby normalnie pracowal.

Z gory dzieki za odpowiedz.

Podaje spisc lspci -nn

00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03)
00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 02)
00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 02)
00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 02)
00:1c.2 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 [8086:27d4] (rev 02)
00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 02)
00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 02)
00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 02)
00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 02)
00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 02)
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2)
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
00:1f.2 IDE interface [0101]: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller [8086:27c4] (rev 02)
00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 02)
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc M56P [Radeon Mobility X1600] [1002:71c5]
04:00.0 Network controller [0280]: Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection [8086:4229] (rev 61)
05:00.0 SATA controller [0106]: JMicron Technology Corp. JMicron 20360/20363 AHCI Controller [197b:2360] (rev 02)
06:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd R5C832 IEEE 1394 Controller [1180:0832]
06:01.1 SD Host controller [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 19)
06:01.2 System peripheral [0880]: Ricoh Co Ltd R5C843 MMC Host Controller [1180:0843] (rev 01)
06:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter [1180:0592] (rev 0a)
06:01.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card Controller [1180:0852] (rev 05)
06:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8110SC/8169SC Gigabit Ethernet [10ec:8167] (rev 10)

[arctgx]

Na temat takiego mniemania trudno cokolwiek powiedzieć. Rozumiem, że jeśli taki top pokazuje duże wartości wa (iowait), to można uczepić się do działania dysku czy kontrolera. Zerknąłbym też na iotop.

Proponowałbym przyjrzeć się, co w dmesg piszczy na temat pracy kontrolera, a w międzyczasie poszukam (również ku własnemu przypomnieniu) jakieś praktyczniejsze polecenie pokazujące, ile przybywa przerwań procesora na tenże kontroler w jednostce czasu.

Na początek można i tak:

Kod: [Zaznacz]

watch -n 1 'cat /proc/interrupts'

[migul]

W dmesgpokazuje mi tak:

Kod: [Zaznacz]

Linux version 2.6.23 (root@Matsu) (gcc version 4.1.2) #19 SMP PREEMPT Mon Dec 15 19:48:45 CET 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000b7fa0000 (usable)
 BIOS-e820: 00000000b7fa0000 - 00000000b7fae000 (ACPI data)
 BIOS-e820: 00000000b7fae000 - 00000000b7ff0000 (ACPI NVS)
 BIOS-e820: 00000000b7ff0000 - 00000000b8000000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
2047MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
Entering add_active_range(0, 0, 753568) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->   229376
  HighMem    229376 ->   753568
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->   753568
On node 0 totalpages: 753568
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 1760 pages used for memmap
  Normal zone: 223520 pages, LIFO batch:31
  HighMem zone: 4095 pages used for memmap
  HighMem zone: 520097 pages, LIFO batch:31
  Movable zone: 0 pages used for memmap
DMI present.
ACPI: RSDP 000FB620, 0014 (r0 ACPIAM)
ACPI: RSDT B7FA0000, 0038 (r1 A_M_I_ OEMRSDT   6000708 MSFT       97)
ACPI: FACP B7FA0200, 0084 (r2 A_M_I_ OEMFACP   6000708 MSFT       97)
ACPI Warning (tbfadt-0442): Optional field "Pm2ControlBlock" has zero address or length: 0000000000000820/0 [20070126]
ACPI: DSDT B7FA05B0, 55B9 (r1  A0650 A0650000        0 INTL 20060113)
ACPI: FACS B7FAE000, 0040
ACPI: APIC B7FA0390, 005C (r1 A_M_I_ OEMAPIC   6000708 MSFT       97)
ACPI: MCFG B7FA03F0, 003C (r1 A_M_I_ OEMMCFG   6000708 MSFT       97)
ACPI: OEMB B7FAE040, 0061 (r1 A_M_I_ AMI_OEM   6000708 MSFT       97)
ACPI: HPET B7FA5B70, 0038 (r1 A_M_I_ OEMHPET   6000708 MSFT       97)
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
ACPI: HPET id: 0xffffffff base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at c0000000 (gap: b8000000:46e00000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
swsusp: Registered nosave memory region: 00000000000e0000 - 0000000000100000
Built 1 zonelists in Zone order.  Total pages: 747681
Kernel command line: auto BOOT_IMAGE=Linux-2.6.23 ro root=301
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1828.815 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2980568k/3014272k available (4702k kernel code, 32540k reserved, 2281k data, 292k init, 2096768k highmem)
virtual kernel memory layout:
    fixmap  : 0xffe15000 - 0xfffff000   (1960 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
    lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
      .init : 0xc07dd000 - 0xc0826000   ( 292 kB)
      .data : 0xc05979c5 - 0xc07d218c   (2281 kB)
      .text : 0xc0100000 - 0xc05979c5   (4702 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Calibrating delay using timer specific routine.. 3660.76 BogoMIPS (lpj=1830384)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
CPU0: Intel Genuine Intel(R) CPU           T2400  @ 1.83GHz stepping 08
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3657.55 BogoMIPS (lpj=1828776)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2400  @ 1.83GHz stepping 08
Total of 2 processors activated (7318.32 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
APIC calibration not consistent with PM Timer: 119ms instead of 100ms
APIC delta adjusted to PM-Timer: 1039061 (1246860)
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  4616.000 MB/sec
xor: using function: pIII_sse (4616.000 MB/sec)
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=6
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH6 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Routing Table [\\_SB_.PCI0.P0P6._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PnPBIOS: Disabled by ACPI PNP
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
pnp: 00:08: iomem range 0x8c000000-0x8c01ffff could not be reserved
pnp: 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
pnp: 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
pnp: 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
pnp: 00:0b: iomem range 0xe0000000-0xe3ffffff has been reserved
pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0c: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0c: iomem range 0x100000-0xb7ffffff could not be reserved
PCI: Bridge: 0000:00:01.0
  IO window: 8000-afff
  MEM window: fdf00000-fdffffff
  PREFETCH window: bdf00000-ddefffff
PCI: Bridge: 0000:00:1c.0
  IO window: c000-cfff
  MEM window: fe900000-fe9fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.1
  IO window: disabled.
  MEM window: fe800000-fe8fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
  IO window: b000-bfff
  MEM window: fe000000-fe7fffff
  PREFETCH window: ddf00000-dfefffff
PCI: Bridge: 0000:00:1e.0
  IO window: d000-dfff
  MEM window: fea00000-feafffff
  PREFETCH window: dff00000-dfffffff
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[b] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
Machine check exception polling timer started.
IA-32 Microcode Update Driver: v1.14a 
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/W].
async_tx: api initialized (async)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:01.0:pcie00]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 3072k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:acaa
vesafb: pmi: set display start = c00cad38, set palette = c00cadfa
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
fb1: Virtual frame buffer device, using 1024K of video memory
ACPI: AC Adapter [AC0] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Lid Switch as /class/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button (CM) as /class/input/input2
ACPI: Sleep Button (CM) [SLPB]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Video Bus as /class/input/input4
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
ACPI: SSDT B7FAE0B0, 0688 (r1    AMI   CPU1PM        1 INTL 20060113)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: SSDT B7FAE740, 0120 (r1    AMI   CPU2PM        1 INTL 20060113)
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
Marking TSC unstable due to: possible TSC halt in C2.
Time: hpet clocksource has been installed.
Switched to high resolution mode on CPU 0
Switched to high resolution mode on CPU 1
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (44 C)
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Linux agpgart interface v0.102
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM/945G/945GM chipsets
intelfb: Version 0.9.4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.14)
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky 
r8169 Gigabit Ethernet driver 2.2LK loaded
ACPI: PCI Interrupt 0000:06:07.0[A] -> GSI 18 (level, low) -> IRQ 18
eth0: RTL8169sc/8110sc at 0xf8822c00, 00:1b:fc:99:7a:50, XID 18000000 IRQ 18
Linux video capture interface: v2.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
Clocksource tsc unstable (delta = -250656421 ns)
hda: WDC WD1200BEVS-60UST0, ATA DISK drive
Probing IDE interface ide1...
hdd: Slimtype DVDRW SSM-8515S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63
hda: cache flushes supported
 hda: hda1
hdd: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache
Uniform CD-ROM driver Revision: 3.20
Loading iSCSI transport class v2.0-724.
iscsi: registered transport (tcp)
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2449]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
sym53c416.c: Version 1.0.0-ac
iscsi: registered transport (qla4xxx)
QLogic iSCSI HBA Driver
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.10-rc5 Thu May 17 10:09:32 PDT 2007
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
ipr: IBM Power RAID SCSI Device Driver version: 2.4.1 (April 24, 2007)
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
SCSI Media Changer driver v0.25
ahci 0000:05:00.0: version 2.3
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ahci 0000:05:00.0: AHCI 0001.0000 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
ahci 0000:05:00.0: flags: 64bit ncq pm led clo pmp pio slum part
PCI: Setting latency timer of device 0000:05:00.0 to 64
scsi0 : ahci
ata1: SATA max UDMA/133 cmd 0xf8824100 ctl 0x00000000 bmdma 0x00000000 irq 16
ata1: SATA link down (SStatus 0 SControl 300)
ata_piix 0000:00:1f.2: version 2.12
ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
ACPI: PCI Interrupt 0000:00:1f.2[b] -> GSI 19 (level, low) -> IRQ 19
PCI: Unable to reserve I/O region #1:8@1f0 for device 0000:00:1f.2
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 0 (errno=-16)
PCI: Unable to reserve I/O region #3:8@170 for device 0000:00:1f.2
ata_piix 0000:00:1f.2: failed to request/iomap BARs for port 1 (errno=-16)
ata_piix 0000:00:1f.2: no available native port
I2O subsystem v1.325
i2o: max drivers = 8
I2O Configuration OSM v1.323
I2O Bus Adapter OSM v1.317
I2O Block Device OSM v1.325
I2O SCSI Peripheral OSM v1.316
I2O ProcFS OSM v1.316
Fusion MPT base driver 3.04.05
Copyright (c) 1999-2007 LSI Logic Corporation
Fusion MPT SPI Host driver 3.04.05
Fusion MPT FC Host driver 3.04.05
Fusion MPT SAS Host driver 3.04.05
Fusion MPT misc device (ioctl) driver 3.04.05
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]  MMIO=[feafe000-feafe7ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfebffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-6: new high speed USB device using ehci_hcd and address 3
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ec00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-6: configuration #1 chosen from 1 choice
usb 4-1: new full speed USB device using uhci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e0180003955989]
usb 4-1: configuration #1 chosen from 1 choice
usb 5-2: new low speed USB device using uhci_hcd and address 2
usb 5-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input5
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:03 failed with error -16
i2c /dev entries driver
ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 19 (level, low) -> IRQ 19
Synaptics Touchpad, model: 1, fw: 6.1, id: 0xa3a0b3, caps: 0xa04713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input6
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
iTCO_vendor_support: vendor-support=0
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    585 MB/s
raid6: int32x2    656 MB/s
raid6: int32x4    574 MB/s
raid6: int32x8    484 MB/s
raid6: mmxx1     1550 MB/s
raid6: mmxx2     1816 MB/s
raid6: sse1x1    1277 MB/s
raid6: sse1x2    1714 MB/s
raid6: sse2x1    2011 MB/s
raid6: sse2x2    2210 MB/s
raid6: using algorithm sse2x2 (2210 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath emc: version 0.0.3 loaded
device-mapper: multipath rdac: rdac: version 0.4 loaded
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCI H4 protocol initialized
Bluetooth: HCI BCSP protocol initialized
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:06:01.1 [1180:0822] (rev 19)
ACPI: PCI Interrupt 0000:06:01.1[b] -> GSI 17 (level, low) -> IRQ 17
mmc0: SDHCI at 0xfeafec00 irq 17 DMA
usbcore: registered new interface driver hiddev
input: A4Tech RF USB Mouse as /class/input/input7
input: USB HID v1.11 Mouse [A4Tech RF USB Mouse] on usb-0000:00:1d.3-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
oprofile: using NMI interrupt.
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
arp_tables: (C) 2002 David S. Miller
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
tunl0: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
NET: Registered protocol family 4
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO (Voice Link) ver 0.5
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: BNEP (Ethernet Emulation) ver 1.2
Bluetooth: BNEP filters: protocol multicast
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
Using IPI No-Shortcut mode
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Replacing swsusp.
TuxOnIce: Resume= parameter is empty. Hibernating will be disabled.
Compression Driver: Argh! Nothing follows me in the pipeline!
compression didn't initialise okay.
TuxOnIce: Initialise modules failed!
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 292k freed
net eth5: device_rename: sysfs_create_symlink failed (-17)
udev: renamed network interface eth0 to eth5
intel_rng: FWH not detected
asus-laptop: Asus Laptop Support version 0.42
asus-laptop: Error calling BSTS
asus-laptop:   Z96JM model detected
Registered led device: asus:mail
fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[fglrx] Maximum main memory to use for locked dma buffers: 2767 MBytes.
[fglrx] ASYNCIO init succeed!
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
[fglrx] PAT is enabled successfully!
[fglrx] module loaded - fglrx 8.44.3 [Dec 19 2007] on minor 0
hda_codec: Unknown model for ALC882, trying auto-probe from BIOS...
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[fglrx] Reserve Block - 0 offset =  0X1000000 length = 0X5000
[fglrx] Reserve Block - 1 offset =  0X0 length = 0X1000000
[fglrx] Reserve Block - 2 offset =  0Xffff000 length = 0X1000
[fglrx] Reserve Block - 3 offset =  0Xffbf000 length = 0X40000
r8169: eth5: link up
eth5: no IPv6 routers present
/dev/vmmon[3613]: Module vmmon: registered with major=10 minor=165
/dev/vmmon[3613]: Initial HV check: anyNotCapable=0 anyUnlocked=0 anyEnabled=1 anyDisabled=0
/dev/vmmon[3613]: HV check: anyNotCapable=0 anyUnlocked=0 anyEnabled=1 anyDisabled=0
/dev/vmmon[3613]: Module vmmon: initialized
/dev/vmnet: open called by PID 3663 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 3664 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 3665 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 3695 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 3696 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
vmnet1: no IPv6 routers present
vmnet8: no IPv6 routers present

Podejrzewam ze nie jest wlaczony jakis sterownik w jajku systemu. Nie wiem jak znalesc odpowiedni sterownik tudziez modul zeby prace aplikacji jechaly po dysku a nie procesorze.

________
arctgx: BBCode

Przy okazji, znacznik pogrubienia (b) został tyle razy wyzwolony w komunikacie, że szkoda naprawiać...

[arctgx]

Używaj, proszę, CODE: http://forum.linux.pl/help.php#bbcode

Może na początek: dlaczego zainstalowałeś tak stare jądro? Może zamiast wnikania, lepiej od razu wypróbować na nowym? Wersja 2.6.23 (choć Twoja jest poprawioną sprzed roku) ma już prawie dwa lata.

[migul]

Bo jestem lewy z linuxa i uzywam wersji ktora stworzyl sobie moj kumpel. Troche nad nim juz siedze ale jeszcze nigdy nie robilem tak doglebnych rzeczy. Po za tym wiem ze u niego ta wersja jajka chodzi z dyskiem sata bardzo dobrze. Wiec podejrzewam ze u mnie tez sie da a po za tym nie chcialbym zmieniac jadra bo boje sie ze cos pojdzie nie tak i strace dane.

[arctgx]

Nie mógłbyś zamiast instalacji, wypróbować po prostu jakiejś wersji live CD, np. Ubuntu 9.04 lub 9.10 alfa6?

[migul]

No wlasnie nie bardzo. Mam juz system który mniej wiecej jest juz skonfigurowany pod moja firme i nie chcialbym jakos specjalnie w nim grzebac. CHodzi mi tylko o ustawienie tych steronikow i tyle.

[mateo86]

Z tego co widzę to płyta główna jest Asusa, przynajmniej specyfikacja bardzo podobna do mojej...

W jajku od 2.6.28 domyślnie są włączone wszystkie sterowniki potrzebne do poprawnej pracy systemu na tej płycie (poza kartą sieciową)...

Jak chcesz, mogę podesłać Ci swoje jajko, chociaż niekoniecznie musi ono działać...

Wydaje mi się, czy masz macierz raid? Może to ona jest powodem tych problemów?

[migul]

Komp to jest dokładnie laptop Asustek S96S tak ze raida fizycznie nie ma chyba ze jest wlaczona opcja taka. Co do jajka to nawet jak mi przeslesz to mem ryzyko czy faktycznie zadziala no i nie wiem czy sobie poradze ze zmiana jego na inna wersje.

[flak]

Mam tu ASmobile (nie licencjonowany ASUS) S96SP na Kubuntu 9.04 (kernel 2.6.28) i chodzi w porządku poza tym że kamera internetowa nie działa ale po prostu jeszcze się za nią nie brałem. Poza tym co do obsługi hardwaru nie mam zastrzeżeń. Na Kubuntu 8.04 (kernel 2.6.28) też działał w porządku.  

Dwie sprawy:

Podmiany kernela  na niestandardowy, np. z nowszej serii, dla laika to kiepski pomysł bo ewentualne poprawki (w tym bezpieczeństwa) będzie trzeba nakładać ręcznie. Zmiana dystrybucji na nowszą to zdecydowanie lepszy pomysł. Ubuntu 8.04 LTS będzie wspierany do kwietnia 2011 więc raz postawisz i będziesz miał spokój na ponad 2 lata a nie rok z "hakiem".  

Twoje problemy wcale nie muszą oznaczać problemu z sterownikami sata.